Change Log
[1.10.0] - 2025-06-30:
Main changes since 1.9.0
Tested Segger Embedded Studio Version: 8.24
Tested Zcc toolchain 4.0.0
Changed:
soc: HPM5300/HPM6E00/HPM6P00: update soc files.
soc: toolchain/bootheader: rename XPI0 to FLASH.
linker: ld: add ALIGN(8) into ‘start section’ and before symbol ‘__etext’.
drivers: pllctl: add spread spectrum setup api.
drivers: pllctlv2: add api to setup spread spectrum.
drivers: qeiv2: add some config apis.
drivers: qei: add some config apis.
drivers: usb: add delay in usb phy de-init.
drivers: eui: rename eui_get_time() to eui_get_time_us().
drivers: sei: update sei driver based on sei.csv update.
drivers: sei: add macro SEI_DAT_CMD.
drivers: sei: add synchronous slave rx tx point macros.
drivers: pmp add api to configure and lock pmp and pmp entry separately.
drivers: pdm add configure sample rate API.
drivers: tsw: add an API tsw_cb_frer_set_msec_cycles().
drivers: tsw: add struct rx_hdr_dest_t definition.
drivers: spi: add spi_master_enable_cs_select API.
drivers: mcan add mcan_is_tx_buf_cancellation_finished.
drivers: gptmr: fix assignment and spelling errors in burst mode API.
boards: hpm5301evklite: use XTAL as pll ref clock.
boards: add clk_ref pin information.
boards: hpm6p00evk: add spi0 clock for board_init_spi_clock API.
components: usb: components: add attached_buffer and attached_qtd in dcd_qhd_t.
components: plb components: config all input trig pins for each channel.
components: usb: components: format hpm_usb_device.c file.
components: usb: components: avoid to use qtd buffer addr to calculation.
components: serial_nor: add hpm_serial_nor_get_tx_dma_mgr_resource and hpm_serial_nor_get_rx_dma_mgr_resource APIs.
components: serial_nor: add dma_mgr to implement internal DMA management.
middleware: cherryusb: middleware: fix build warning.
middleware: lvgl: add lv_app_conf.h.
middleware: cherryusb: update to v1.5.0.
middleware: cherryusb: update isr organization for otg.
middleware: cherryusb: fix ehci_qtd_alloc() not init qtd alt_next_qtd and token.
middleware: cherryusb: implement usb_hc_low_level_deinit().
middleware: cherryusb: middleware: add qtd pool to qh usage.
middleware: usb: update _dcd_data aligned settings.
middleware: fatfs: update sdmmc port, don’t need cache maintain here.
middleware: fatfs: update spi_sd port, don’t need cache maintain here.
middleware: fatfs: support cacheable buffer read and write.
middleware: add CONFIG_XXX_CUSTOM_PORTABLE to exclude port layer.
middleware/components: usb device: add usb_qtd_alloc() to ep usage, enabled by macro USB_DEVICE_DTD_POOL_SHARED.
middleware: cherryusb: sync to cherryusb v1.5.0 release.
middleware: canopen: update canopen module to master branch.
middleware: ucos_iii: replace CONFIG_UCOS_III_TIMER_RESOURCE_NOT_MCHTMR with CONFIG_UCOS_III_TIMER_RESOURCE_GPTMR.
middleware: freertos: support for using pwm as FreeRTOS’s tick source.
middleware: fatfs: add break when disk_read/write failure.
samples: coremark/dhrystone: adjust options for zcc.
samples: drivers: samples: split sample to separate examples.
samples: drivers: samples: split to two separate examples.
samples: qei/qeiv2: use qei_config_mode()/qeiv2_config_mode() APIs.
samples: usb: device samples: decrease msc_disk size from 32KB to 8KB.
samples: cherryusb: update usb_config.h file to adapter to v1.5.0.
samples: cherryusb: samples: delete USBH_USE_CUSTOM_ISR and USBD_USE_CUSTOM_ISR.
samples: cherryusb: samples: rndis: optimize linkoutput API, wait for current frame to complete.
samples: cherryusb: samples: rndis: samples: set NO_SYS=0 to enable OS support in lwip.
samples: cherryusb: samples: msc: delete the limitation about the cluster size.
samples: tsn: samples: simply ip, gw, netmask and mac.
samples: sei: samples: add disable_instr_ptr_check init in latch2.
samples: rgb_led: samples: add some descriptions.
samples: rgb_led: samples: add implementation description.
samples: rgb_led: remove redundant code.
samples: rgb_led: add code comments in detail.
samples: drivers: samples: update endat rewind cmd register config.
samples: sei: use macro SEI_DAT_CMD.
samples: sei: samples: use SEI_SYNC_SLAVE_RX_TX_POINT_ON_xxxx_EDGE macros.
samples: drivers: samples: update irq flag processing.
samples: sei: samples: bissc/endat: support auto adjust rx point.
samples: imgae: samples: align file_buffer to cache line size.
samples: image: delete cache maintain in file_store() and file_restore().
samples: audio: update audio related buffer aligned size.
samples: sd_fatfs: align buffer address to cache line size.
samples: spi_sdcard: remove ATTR_PLACE_AT_NONCACHEABLE for FATFS and FIL variable.
samples: usb: samples: use FATFS_ONLY_NONCACHEABLE_BUF macro.
samples: plb samples: support filter mode change.
samples: tsn_free_preemption_ingress: update log for readme_en.rst.
samples: bgpr: update readme doc.
samples: motor_ctrl: refactor QEI/QEIV2 and PWM initialization.
samples: cherryusb: cdc samples: change readbuf to ping-pang buffer.
samples: pllctlv2: samples: change debug uart clock src.
samples: pllctl/pllctlv2: exclude all flash and sdram targets.
samples: cherryusb: update uvc yuyv sample.
samples: drivers: samples: add screenshots of spread spectrum.
samples: qeov2: add code comments and update README.
samples: qeo: add code comments and update README.
samples: sdm: add code comments and update README.
samples: drivers: samples: change GPTMR clock source enabling to board_init_gptmr_clock API.
samples: uart_lin: add code comments and update README.
samples: lin: add more comments and update README.
samples: i2s_master/slave: add more comments and update README.
samples: i2s_dma: add more comments and update README.
samples: i2s_interrupt: add more comments and update README.
samples: i2s_dao_pdm: add comments and update README.
samples: coremark/dhrystone: adjust options for zcc.
samples: add hpm_pdmlite_drv.h.
samples: i2s: update pdm and dao sample.
samples: canopen: split the sample of canopen into master role and slave role.
samples: ucos_iii: merge ucos_iii hello and ucos_iii hello mchtmr samples.
samples: threadx: merge threadx hello and threadx hello mchtmr samples.
samples: freertos: update freertos hello to support pwm as tick source.
samples: tsn: samples: add broadcast frame and unknown frame action settings.
samples: tsn: samples: enhance the ability to resist network stroms.
samples: tsn: samples: update some configurations parameters to improve throughput.
samples: tsn: samples: common: remove a redundant function call netif_set_link_up(netif).
samples: dhrystone: clear compile options for non zcc compiler.
samples: drivers:mcan add demo for txbuf cancellation.
samples: coremark: using set RV_ABI and RV_ARCH instead of sdk_ses_compile_options().
samples: update pwmv2 sync, add note for restore pwmv2 state.
samples: sei: update lacth-state config flow to enhance readability, and move irq enable after engine enable.
samples: drivers: samples: dma_use_gptmr_event_transfer: change GPTMR clock source enabling to board_init_gptmr_clock API.
samples: i2s: add i2s_config_multiline_transfer APi description.
samples: fft_perf_test: improve README documentation clarity.
docs: samples: docs: gpio: update the description for readme.
docs: samples: docs: gpiom: update the description for readme.
docs: samples: docs: gptmr: add readme doc for index.rst.
docs: samples: docs: update FIFO threshold description for readme.
docs: samples: docs: spi: add readme doc.
docs: samples: docs: add readme doc for index.rst.
docs: samples: update cherryrb and cherryusb usbnet samples readme.
docs: update cmake_intro file.
docs: add separate target for en/zh.
docs: samples: add mm_align readme to index.
docs: update sdk schedule.
docs: samples: docs: uart: add hardware flow control description for index.rst.
docs: update some samples titles and board readme.
docs: add i2s peripheral README.
docs: samples: docs: update the description for hardware CS.
docs: samples: docs: uart: add interrupt description.
docs: samples: docs: gptmr: add burst mode description.
cmake: segger: add HPM_SES_USE_SEGGER_LD definition.
cmake: zcc: show memory usage after build.
cmake: add comments in detail for all functions.
cmake: ses: process -Ox for ses_cflags.
cmake: normalize heap/stack size.
cmake: add human readable size string parsing.
Fixed:
soc: hpm6800: fix incorrect dram size in linker files.
soc: uart: add uart tx idle feature.
soc: clock clarify the behavior of clock_wait_source_stable.
soc: update soc hpm_gpiom_regs.h.
soc: update HPM6E00 and HPM6P00 header files.
soc: toolchains:iar fix fw_size value.
soc: toolchain: soc: correct fw_size.
soc: enet: fix buff address alignment.
drivers: uart: prescaler calculation changed from floating-point to integer for uart_calculate_baudrate API.
drivers: qei: rename QEI_EVENT_POSITIVE_COMPARE_FLAG_MASK to QEI_EVENT_POSITION_COMPARE_FLAG_MASK.
drivers: pmp correct the value for PMP_ADDR and PMA_ADDR.
drivers: uart: enhance divider calculation by adding rounding for uart_calculate_baudrate API.
drivers: eui: fix filter length settings.
drivers: sdm: fix output 16bit data.
drivers: uart: add missing tx idle configuration in uart_init function.
drivers: uart: change uart_enable_9bit_transmit_mode function macro condition.
drivers: uart: change tx idle function macro condition.
drivers: pmp fix calculation of PMPADDR and PMAADDR.
drivers: tsw: fix bitfield IRQEN in register MM2S_DMA_CR setting error.
drivers: pllctl: fix pll stable judgement and wait pll stable after change pll frequency.
drivers: pllctlv2: fix pll stable judgement and wait pll stable after change pll frequency.
drivers: qeiv2: fix iar build warning.
drivers: pwmv2 modify function note.
drivers: synt channel 4-15 can not use.
drivers: pllctlv2: fix calculation overflow issue.
drivers: tsw: update some register names.
boards: hpm6p00evk: fixed incorrect SPI2 clock value return in board_init_spi_clock API.
boards: hpm6p00evk: remove LIN info in README.
boards: hpm6p00evk: fix uart pin position.
boards: hpm5300evk: fix link of drv_lv50a_mp1907 in zh doc.
boards: add sdram card detect function.
boards: hpm6e00evk fix typo in board_init_can_clock.
components: usb: components: enable ios interrupt when open ep0.
components: plb: resolve sign comparison warning in LIN clock detection.
components: usb: components: fix dtd buffer address setting.
components: hpm_jpeg: fix build warning.
middleware: tflm: Fix const qualifier in flatbuffers stl_emulation.h.
middleware: fix freertos bug when using gptmr and enable preempt.
middleware: usb: middleware: fix control transfer processing.
middleware: fatfs: fix disk_ioctl data type.
middleware: lvgl: fix stride mismatch.
middleware: tinyusb: middleware: delete vTaskDelay from isr.
middleware: hpm_sdmmc support disabling the sdmmc xfer callback.
middleware: ucos_iii: fix preemption problem.
middleware: decoder_wav: fix wav header decode problem.
middleware: uCOS-III: add check for vector mode in port.c.
middleware: enhance motor angle alignment support.
middleware: segger_rtt fix compiling issue when using ses with andes toolchian.
samples: delete disable trig function in qei init.
samples: delete disable oneshot mode function in qei init.
samples: sei: samples: fix crc configuration.
samples: sdm: update data to voltage convert function.
samples: fix ‘enable’ spelling errors.
samples: image: samples: add cache invalidate before encode.
samples: image: samples: add cache invalidate before encode.
samples: image: samples: fix pdma src buffer don’t have cache maintain.
samples: mhd_wifi_demo: exclude lwip for clang.
samples: lwip:mhd_wifi_demo add missing lwip portable layers.
samples: lwip:mhd_wifi_demo avoid using the common lwip config.
samples: lwip_iperf: fix compiling error.
samples: bgpr: add default build type.
samples: lwip: samples: eliminate clang-tidy check errors.
samples: sent: samples: add the -lm option to link the math library.
samples: fix netx build error.
samples: netxduo: add support for specifying port in cmd line.
samples: pllctlv2: remove ss type.
samples: cherryusb: audio samples: fix feedback ep no data.
samples: cherryusb: samples: http_server_freertos: exclude ram_release build type.
samples: fix OpENer samples restart error when link down.
samples: rom_api:sdp_api correct wrong ROM API call.
samples: fix the bug that the lsb of POS is covered to zero.
samples: dhrystone: correct compile options.
samples: i2s: remove unnecessary included drivers.
samples: tsn: samples: fix missing flow meter configurations.
samples: tsn: samples: lwip_tcpecho: fix the issue that port number cant not be redefined.
samples: tsn: samples: common: fix extreme low throughput with interrupt usage.
samples: rom_api:xpi_nor_api avoid inlining ram function into function at FLASH.
samples: spi_sdcard: samples: fix large file write test failed with IAR release build.
samples: fix iar relocation issue for the software library in flash_sdram_xip build.
samples: drivers: samples: dma_use_gptmr_event_transfer: fix no led blimk for hpm5e00evk.
samples: sent: samples: align pwm_meas_table to 8-byte boundary when transfer size is 8 bytes in XDMA.
samples: drivers: samples: fix documentation description errors and duplicates.
samples: lwip:mhd_wifi_demo fix demo crashing due to enabling xfer callback.
samples: iperf: fix the tcp receive speed problem of iperf on NetX Duo.
samples: image: samples: fix create new file incorrect.
samples: cherryusb: samples: add volatile to isr variable ‘rndis_tx_done’.
samples: tsn: samples: master / samples: remove a redundant function call of vTaskStartSchedule().
samples: bgpr: re-init bgpr data when cmp failure.
samples: lwip/modbus/multicore/opener/tsn: samples: fix the spelling error.
samples: pllctlv2: change debug uart source clock to osc24m.
samples: retry connect to server if connect error.
samples: put var dhcp_client to zero init section.
samples: jpeg_encode: fix cache incorrect.
samples: lvgl_audio_player: filter music files which can’t decode.
samples: move nonvector definition to middleware from ucos samples.
samples: lwip_ping_freertos_socket: fix compilation error.
samples: i2s_emulation: fix exception caused by input 4 with no recording.
samples: audio: fix pdmlite dependency.
samples: lwip: samples: ethernetif: fix rx task stack overflow when FPU is enabled.
docs: add note info abort enabling dhcp in udp sample readme.
docs: drivers: docs: fix some description errors.
docs: samples: docs: i2c: fix spelling errors.
docs: samples: docs: uart: fix incorrect links issue.
docs: samples: docs: i2c: fix incorrect descriptions for index.rst.
docs: samples: docs: fix incorrect spi_component link.
docs: remove not-needed symbols from sample index file.
docs: get_started: group-tab should be used for OS.
docs: samples: docs: gptmr: fix documentation description errors.
docs: samples: docs: uart: fix documentation description errors.
docs: components: docs: remove duplicate information.
docs: add more information for opener samples.
docs: get_started: fix indent issue.
docs: components: docs: fix RST formatting.
cmake: ses: only convert -flto to ses when using segger compiler.
cmake: iar: correct ld option processing.
cmake: compare_target_sdk_version: correct compare.
scripts: ses: fix windows path issue.
Added:
soc: add hpm5e00 support
drivers: i2c: add i2c_get_fifo_size API.
drivers: sei: add some APIs.
drivers: add pdmlite driver.
drivers: gptmr: add APIs for burst mode.
boards: add hpm5e00evk support
boards: add board_init_gptmr_clock API.
components: hpm_log: add hpm_log.
components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_blocking API.
components: add mm_align component.
components: add capacity related param to sd_card_t.
components: add hpm_sdmmc non-blocking read/write api.
components: dma_mgr: add APIs to request dma resource from specified DMA.
middleware: motor_ctrl: add step motor close loop.
middleware: add middleware doc.
middleware: motor_ctrl: add hardware hybrid loop support for MCL.
samples: motor_ctrl: add step_motor_closed_loop demo.
samples: lvgl: add lvgl_indev_usb_keyboard_mouse sample.
samples: add mm_align sample.
samples: motor_ctrl: update bldc foc demo.
samples: cherryusb: add uvc mjpeg sample.
samples: tsn: samples: add an lwip_iperf samples.
[1.9.0] - 2025-03-31:
Main changes since 1.8.0
Tested Segger Embedded Studio Version: 8.22a
Tested Zcc toolchain 3.2.5
Known Issue:
zcc lld 3.2.5: sections with NOLOAD attribute might be linked incorrectlyi.
It will be fixed in the next toolchain’s release.
zcc libnn 3.2.5: tpt_elementwise_add_s8 incorrect input parameter sign, it will be fixed in the next toolchain’s release.
It will be fixed in the next toolchain’s release.
Workaround: refer to README of samples/tflm/face_obj
Changed:
arch: l1c: add macro HPM_SDK_L1C_NO_REENTRANT.
arch: l1c: move cache size macros from arch to soc feature.
arch: l1c: update cache mcctl data API.
arch: l1c: remove disable and enable interrupt.
arch: l1c: optimize cache operation.
soc: pcfg: update pcfg_wakeup_src_t enum.
soc: rename pdgo wakeup enable and disable APIs.
soc: interrupt: stack sp should be align 16 bytes.
soc: update trap and interrupt to save and restore mcctl data.
soc: l1c: unify cache driver.
soc: update some compiler options for zcc-3.2.5.
soc: hidden adc12/adc16 BUS_RESULT registers svd.
soc: l1c: add api to enable writearound.
soc: update soc header from hpm_soc_info.
soc: hpm6p00 update soc part number.
soc: triggermux, release TRIM_IN TRIM_OUT registers for hpm6pxx.
soc: update hpm200/hpm1200/hpm600/hpm700 soc files.
soc: using pllctlv2 driver enum pll/clk/div.
drivers: hpm_common: macro ATTR_PLACE_AT_NONCACHEABLE and ATTR_PLACE_AT_FAST_RAM keep for backwards compatibility.
drivers: mcan change the Message Buffer setting logic.
drivers: uart: add and modify uart_fifo_trg_lvl_t enum members to accommodate different SOC uart FIFO depth.
drivers: pllctlv2: add enum for pll/clk/div.
drivers: tsn: add enum definitions for mac types.
drivers: acmp: add the extended filter length setting API.
drivers: acmp: delete clock and cap settings.
drivers: DMA: remove unused bit.
drivers: trgm: rename trgm_input_filter_xxxx apis to trgm_filter_xxxx apis.
drivers: pdgo: suppress clang-tidy warning.
drivers: gptmr: differentiate between swsynct assignment in QEI and non-QEI for gptmr_trigger_channel_software_sync API.
drivers: ptpc and i2c bringup.
drivers: tfa add common lib.
drivers: move pdgo driver to soc folder.
drivers: add ewdg bit18 stop_wdt_aft_reset.
drivers: gptmr: add qei mode related APIs.
drivers: spi: add slave cs falling and rising edge interrupt enum.
drivers: spi: add enable/disable dma request after cmd APIs.
drivers: uart: update uart driver.
drivers: qeov2: add new position filter function.
drivers: esc: add byte read/port disable/sync irq map function.
drivers: qeiv2: round adc cfg param.
drivers: romapi move common xpi and xpi nor API table to driver.
drivers: update lobs drivers.
drivers: lobs: update lobs driver.
drivers: lobs: update lobs driver for v1.0.0.
drivers: jpeg: update jpeg configurate.
boards: hpm6p00evk: update sdram size and width.
boards: set TEST_DMA_CONTROLLER to XDMA if XDMA exist.
boards: doc: add board know issue description.
boards: hpm6p00evk: change plb output pins.
boards: hpm6p00evk: update board readme doc.
boards: hpm6p00evk: update device name.
boards: add build flag to exclude board timer functions.
boards: bump up vcore to 1275mv and update to OD freq.
boards: Change the naming of trgmux-related macros.
boards: openocd: update flash option in board config.
boards: hpm5300,hpm6p00,hpm5300 change default flash freq to 100mhz.
boards: hpm6p00evk: update flash config as sip part is used.
boards: adc16: adjust pinmux to be the same as ACMP pin for auto test.
boards: hpm6p00evk update soc name and on-board flash size.
boards: add qeo pwm safety trgm definition.
boards: hpm6800evk: add board_puart_pin feature.
boards: change IRQn_SEI_x to IRQn_SEI0_x.
boards: hpm5300evk: add ecat port2 pin config and definition.
boards: hpm6p00evk: add a note about enet initialization error when ISP mode is selected.
components: Add hpm_jpeg component.
components: improve encode performance.
components: i2c: add the hpm prefix to the enum and the structures of the i2c component.
components: i2c: change the I2C_Type parameter to hpm_i2c_context_t to pass in configuration parameters.
components: plb: rename trgm_input_filter_xxxx apis to trgm_filter_xxxx apis.
components: update readme for support cache config.
components: ppi: change ns type from uint8_t to uint16_t.
components: ppi: add dq signal select dq pins configuration.
components: spi: enable dma request after cmd for setup_dma APIs.
components: plb_filter: update readme doc.
middleware: cherryusb: update CMakeLists.txt to include audio and video host class.
middleware: cherryusb: middleware: update config to improve performance.
middleware: fatfs: adapter to cherryusb v1.4.3.
middleware: cherryusb: update to v1.4.3.
middleware: threadx: stack sp should be align 16 bytes.
middleware: ucos_iii: stack sp should be align 16 bytes.
middleware: FreeRTOS: stack sp should be align 16 bytes.
middleware: rtthread-nano: stack sp should be align 16 bytes.
middleware: threadx: add save and restore mcctl data.
middleware: rtthread-nano: add save and restore mcctl data.
middleware: ucos_iii: add save and restore mcctl data.
middleware: freeRTOS: add save and restore mcctl data.
middleware: wifi:mhd_wifi upgrade mhd_wifi stack to new revision.
middleware: wifi:mhd_wifi upgrade to new revision.
middleware: cherryusb: msc middleware: update msc host class stack.
middleware: vglite: WB_NO_ALLOC is used by vglite.
middleware: hpm_math: add hpm_dsp_and_u16() API.
middleware: lvgl: support rotate.
middleware: rtthread-nano: update to v4.1.1.
samples: cherryusb: samples: add UDisk format picture.
samples: tinyusb: samples: add UDisk format picture.
samples: cherryusb: samples: update auto and manual operation flow.
samples: cherryusb: msc samples: add usb disk format description.
samples: image and tinyusb samples: add usb disk format description.
samples: femc: samples: update speed result.
samples: rom_api:xpi_nor_api move phase related functions into separate xpi_util API.
samples: bgpr: samples: add known issue linking.
samples: usb: samples: add board known issue.
samples: lwip & modbus samples: delete unused macro related to DHCP.
samples: lwip: samples: simplify macro definitions for IP/Netmask/Gateway/MAC.
samples: pgdo: add dgo_enable_wakeup_src() when init.
samples: bgpr: update readme doc.
samples: motor_ctrl: Move kp ki parameters to board file.
samples: dual_panel: update readme.
samples: rom_api: samples: add app.yml.
samples: lwip: optimization for app-level option configuration files.
samples: cherryusb: adapter to cherryusb v1.4.3.
samples: move the sent_signal_decode demo from samples/drivers/gptmr to samples/sent/decode.
samples: add support for specify ip address through cmd line.
samples: drivers:mcan set the mcan message buffer explicitly.
samples: lwip:mhd_wifi_demo enable the interrupt-driven mode by default.
samples: drivers: samples: improve print messages for FIFO mode.
samples: i2c_components: since the i2c component API parameter transfer has changed, the parameter variable needs to be modified.
samples: tsn: rename project name to tsn_lwip_tcpecho_example in sample-level CMakeLists.txt.
samples: tsn: samples: tsn_frame_preemption_ingress: modification for compatibility between different port speeds.
samples: lwip: replace tx_buff/rx_buff with cacheable_memory.
samples: ecat: add description to modify port count in ESI.
samples: pwmv2: update pwmv2 fault api.
samples: motor_ctrl: use the new time macro.
samples: motor_ctrl: samples: change the pid parameter to the new loop time.
samples: qeo_pwm_out: add qei provide position to qeo.
samples: ecat: update board phy and led config.
samples: ppi: add cache config for async_sram.
samples: ppi: samples: delete break when mismatch.
samples: qeiv2: samples: add macro BOARD_APP_QEI_TRIGMUX_OUT_NUM_ADC.
samples: drivers: samples: reorganize pdgo demo depend by soc.
samples: ppi: add dq signal select dq pins.
samples: drivers: samples: add qeimode sample.
samples: drivers: samples: interrupt: add CS rising and falling edge interrupt detection.
samples: drivers: samples: update uart_rx_line_status sample.
samples: ecat: update flash emulate eeprom component address.
samples: lobs: update lobs sample.
samples: spi samples: update the readme for all sample.
samples: trace_recorder, update for rtthread v4.1.1.
samples: update rtthread config files.
samples: rtthread-nano, update demo, adapt v4.1.1.
samples: sei: master: endat/nikon: should be use sei_set_trig_input_command_value() instead of sei_set_command_value().’
samples: sei: slave: update baudrate settings.
docs: samples: docs: update the runtime behavior description.
docs: ppi: ppi memory cache only support MEM_TYPE_MEM_WB_READ_WRITE_ALLOC.
docs: convert docs from md to rst.
docs: samples: docs: update related API usage tips.
scripts: exclude ucos-iii commit check.
readme: remove releases after v1.10.0.
Fixed:
soc: gcc: soc: correct typo of fini_array section.
soc: pcfg: fix pcfg_clear_wakeup_cause() API.
soc: HPM6P81: update SPI_SOC_FIFO_DEPTH to 8.
soc: HPM6E80: update SPI_SOC_FIFO_DEPTH to 8.
soc: l1c: correct shift value.
soc: l1c: add l1c_xc_unlock.
soc: fix rtos build error.
soc: hpm5301: romapi fix duplicated definition issue.
soc: HPM5301: add clock_mot0 enum for trgm and synt peripheral.
drivers: pwmv2: deinit function error.
drivers: femc: add auto_refresh_cmd_count in config struct, default value is 8.
drivers: enet: add a commnet aboout ENet DMA initialization error.
drivers: tsw: fix the unmatched send id issue.
drivers: opamp: change opamp dac pins.
drivers: spi: prefix ‘spi_’ to spi_shift_direction_t enum members.
drivers: pllctlv2: fix incorrect mask clear.
drivers: sdxc fix SDXC_STS_CMD_ERR definition.
drivers: pixelmux: fix rgb data source disable.
drivers: fix iar build error.
drivers: tsw: fix communition failure after port speed changes.
drivers: pwmv2, fix compile warning.
drivers: pwmv2: fix the name of the pwm api.
drivers: uart: irq mask changes the enum to uint32t for uart_disable_irq API and uart_enable_irq API.
drivers: fix ewdg ot_int_ticks never read build error.
drivers: pdgo: fix turnoff clock source comment.
drivers: tsw: fix function error of API tsw_tsync_update_data.
boards: hpm6p00evk: decrease femc clock from 166MHz to 133Mhz and decrease femc DQ pins driver strength.
boards: hpm6750evkmini: fix lcdc timing to hpw.
boards: hpm6p00evk: improve femc DQ pins speed and driver strength.
boards: hpm6p00evk: boards: Fix foc demo not working.
boards: hpm6p00evk: fix led on level.
boards: hpm6p00evk: add usb_p and usb_n pins initialization.
boards: hpm6p00evk: Add pull-up configuration on RX pin to prevent data reception errors.
boards: put timer_cb under macro NO_BOARD_TIMER_SUPPORT.
boards: hpm6p00evk, flash size is 1MB.
boards: hpm6p00evk flash parameter error.
boards: hpm6e00evk: replace the gptmr sync channel pin, GPTMR0-CH0 -> GPTMR4-CH3.
boards: pwmv2, fix fault pinmux error.
boards: hpm6p00evk: add development board version in note about enet initialization error with ISP boot mode.
components: spi: Rename hpm_spi_dma_install_callback API to hpm_spi_dma_mgr_install_callback API.
components: i2c: Rename hpm_i2c_dma_install_callback API to hpm_i2c_dma_mgr_install_callback API.
middleware: hpm_sdmmc fix the issue that the emmc driver doesn’t support byte addressing mode.
middleware: fatfs: fix usb_disk_read() and usb_disk_write() function prototype.
middleware: cherryusb: fix usbd core stack.
middleware: threadx: fix build errors.
middleware: rtthread-nano, shell add IAR support.
middleware: rtthread-nano,add fpu switch.
middleware: rtthread-nano, thread stack add fpu and rv32e support.
middleware: rtthread-nano, modify thread_pointer initial value.
middleware: rtthread-nano, add iar support.
middleware: hpm_sdmmc: spi middleware: fixed the SD card identification information error issue in version 1.0.
middleware: lwip: middleware: fix some files being sourced twice.
middleware: hpm_sdmmc: spi middleware: open the us delay time.
middleware: Fix uC/OS-III gptmr hello world IAR project error.
middleware: align FreeRTOS initialise task stack to 16 bytes.
middleware: fix freeRTOS cache related stack save&restore code.
middleware: fix canopen mcan init fail.
samples: lwip_ping_freertos_socket: samples: fix comment style warning.
samples: lwip_xxpecho_rtthread-nano: fix main stack overflow issue.
samples: lwip_ping_freertos_socket: fix ping error with static ip.
samples: sent: samples: return error on incomplete or invalid SENT signal decoding.
samples: drivers: samples: sram: fix femc init twice when using flash_sdram_xip build type.
samples: microros add toolchain version information.
samples: ppi: update cache config.
samples: lwip:mhd_wifi_demo fix compiling issue when GCC 14.x is used.
samples: drivers: samples: fix pwmv2 fault run error.
samples: lwipipip_lwip_tcpecho_multi_ports_xxxx: fix program running blocking.
samples: drivers: samples: fix issue with missing parameters in printf output.
samples: lwip_ping_freertos_socket: fix function error.
samples: image: samples: fix op aligned APIs.
samples: motor_ctrl: samples: change hfi parameters.
samples: usb: samples: fix label error.
samples: webusb/bpgr: fix led on/off level.
samples: lvgl_coremark: fix freq switch problem.
samples: lwip: samples: use HPM_STRINGIFY.
samples: image: fix w_size in loop.
samples: image: samples: fix codec failed when storage is udisk.
samples: power_mode_switch: use wkup pin to wakeup.
samples: mhd_wifi_demo: exclude lwip for clang.
samples: lwip:mhd_wifi_demo add missing lwip portable layers.
samples: lwip:mhd_wifi_demo avoid using the common lwip config.
samples: lwip_iperf: fix compiling error.
samples: bgpr: add default build type.
samples: lwip: samples: eliminate clang-tidy check errors.
samples: bldc samples: Adjusting pid parameters.
samples: phase_shifting, global variables modified during interruption are optimized.
samples: count_matching, global variables modified during interruption are optimized.
samples: sent: samples: add the -lm option to link the math library.
samples: fix netx build error.
samples: cherryusb: samples: update readme because some PC no window popup.
samples: lwip: samples: add cache writeback before invoking enet transmission API.
samples: tinyuf2: fix cache maintenance address issue.
samples: lwip_tcpclient: fix no expected function about data echo through TCP transmission.
samples: lobs: fix lobs doc errors.
samples: ecat: add default build type.
samples: uart: samples: add the UART FIFO overflow detection condition description.
samples build error caused by tfa_lib.S.
samples: gptmr: samples: Optimized the logic for parsing SENT signals.
samples: gptmr: samples: rename sent_data_formet_t structure to sent_data_format_t.
samples: fix plb no pulse output.
samples: spi_sdcard: change SPI sdcard send buffer from AHB SRAM to non-cacheable memory.
samples: i2c_components: samples: polling: correction the project name.
samples: tsn: samples: fix logic missing of disabling pmac before pmac setting.
samples: tsn: tsn_stmid_frer_xxx & samples: delete unused function call of tsw_ep_enable_all_mac_ctrl().
samples: ecat: exclude ram target.
samples: fix low power samples soc name.
samples: uart_tamagawa: remove usused hpm_trgm_soc_drv.h.
samples: bldc_block: change loop run time.
samples: uart_lin_slave_baudrate_adaptive: fix pin setting and definition.
samples: qeov2_pwm_out: fix used trgm signal.
samples: qeov2_abz_out&qeov2_pwm_out: fix API unused build warning.
samples: tfa gcc build error.
samples: tfa gcc build error.
samples: sdm: update pwm function to generate clock for sdm.
samples: tsn: fix using a wrong macro for the send buffer assignment.
samples: sei: samples: nikon: fix CDF crc error.
docs: components: docs: fix parameter description errors in hpm_spi_set_sclk_frequency API doc.
docs: the jump link for “get_started” on the homepage is invalid.
docs: tflm: docs: add zcc libnn 3.2.5 compiling config.
docs: rdc: change rdc readme error.
docs: samples: docs: uart_irq: when switching RST doc, need migrate updated MD doc.
docs: bldc_block: add hall pin description.
docs: zh: Fix the link failure in the ‘Pin Description’ section of the Chinese doc.
docs: boards: docs: en: fix the incorrect display of GPTMR pins.
docs: boards: docs: Remove unnecessary comments.
docs: remove ‘lab_’ prefix from lab_board_resource tags in RST files.
docs: boards: docs: Fix GPTMR4.COMP_0 board position.
docs: rvbacktrace: fix trailing whitespace.
docs: samples: docs: uart_irq: improve the description information of the notes.
cmake: CMAKE_CXX_STANDARD can be specified by user.
cmake: ses: fix missing zicsr zifencei ext while zcc is used.
cmake: fix build path is too long to compile success for core1 of dual demo.
scripts: ses: update c++ standard according to CMAKE_CXX_STANDARD.
scripts: localize_sdk: copy middleware directory.
scripts: add default value for new parameters argv[3-4] in check_board_cap.py. -refs hpm_sdk #3962.
scripts: iar: cc definitions need to be normalized.
scripts: remove the junction folder mapping after core1 generated. -refs sdk_env #3609.
Added:
soc: bpor: add bpor_is_reg_value_retention_enable() API.
soc: HPM6E00 add new part.
soc: sysctl: add sysctl_get_cpu_lp_retention() APIs.
drivers: hpm_common.h: add a macro definition HPM_STRINGIFY.
drivers: tsw: add an API tsw_set_xmac_mode().
drivers: triggermux, add get status function for input signal.
drivers: pwmv2:add some driver interface.
boards: yaml: add board_wkup_pin feature.
boards: add macro BOARD_BGPR.
components: segment_led: add segment led components.
components: panel: add multi panel support.
components: spi: add hpm_spi_get_tx_dma_resource and hpm_spi_get_rx_dma_resource APIs.
components: i2c: add hpm_i2c_get_dma_mgr_resource API.
middleware: dsp: add hpm_dsp_mat_add_f64() API.
middleware: hpm_mclv2: add time conversion related macros.
samples: cherryusb: add webusb serial sample.
samples: add sent signals encode sample.
samples: drivers: add bgpr retention sample.
samples: add segment_led_key sample by using segment_led component.
samples: drivers: samples: add readme files.
samples: pwmv2, point trigger PWM.
samples: pwmv2, add fix duty cycle change frequency sample.
samples: pwmv2 add synchronous output.
samples: pwmv2 add phase shifting sample.
samples: tfa add fpu check.
samples: add tfa driver and sample support.
samples: exclude usbx sample that used too much ram.
docs: components: docs: add new description readme doc.
[1.8.0] - 2024-12-31:
Main changes since 1.7.0
Tested Segger Embedded Studio Version: 8.20
Tested Zcc toolchain 3.2.4
Changed:
soc: TRGMMUX: add description in hpm_trgmmux_src.h
soc: update hpm_core_clock when setting cpu clock
soc: update header files.
soc: unified clock name
soc: update header file from hpm_soc_info
soc: romapi add fencei to xpi nor apis.
drivers:sdxc add new API and optimize the transfer handling logic.
drivers: cam: remove the pack_dir assignments for CR register
drivers: lobs: update lobs driver
drivers: i2c: add status_i2c_bus_busy enumeration member
drivers: femc: update delay cell config
drivers: sei: update wait len for hpm5300 sei async communication
drivers: sei: update hpm5300 asynchronous mode
drivers: i2s: support different tx/rx channel in duplex mode
drivers: camera: pix format support yuv422
drivers: uart: add new API uart_enable_rx_function.
drivers: pwm: Increased output 100 percent duty cycle with centre symmetry.
drivers: tsw: add APIs to support Qbu, CB, and Qci
components: spi: Optimize SPI clock division for hpm_spi_set_sclk_frequency API
components: debug_console: keep symbols used by ses library
boards: remove unused macro BOARD_USB
boards: enable only common clock in board_init_clock()
boards: add board_init_i2c_clock() API
boards: uart and spi use default clock frequency 80MHz
boards: change BOARD_APP_I2S_DATA_LINE to BOARD_APP_I2S_TX_DATA_LINE and BOARD_APP_I2S_RX_DATA_LINE
boards: hpm6800evk reduce ddr io leakage.
boards: HPM6E00evk: add pin setting for uart lin slave
boards: enet: replace with macro for clock setting APIs
middleware: hpm_mcl_v2: add pll filter
middleware: rtt: iar: rtt_risc_v_trap_handler align to 4 byte
middleware: freertos: new critical protection method
middleware: vglite: update to 4.0.87.
middleware: hpm_sdmmc switch to adma3 descriptor by default.
middleware: cherryusb: update video stack to use pingpang buffer
middleware: cherryusb: update to v1.4.2
middleware: lvgl: change vglite mode to cacheable
middleware: lvgl: update lvgl library source.
middleware: wifi: mhd_wifi format the source code.
middleware: rtthread-nano rt_kprintf update to v4.1.1 .
middleware: wifi: mhd_wifi optimize lib including path.
middleware: wifi: mhd_wifi update wifi stack with BSD license.
middleware: add version or changelog
middleware: wifi: mhd_wifi add license and changelog.
middleware: hpm_sdmmc: mmc,sdio optimize cache-maintenance efficiency.
middleware: hpm_sdmmc: hpm_sdmmc_host add new API and optimize transfer logic.
samples: uart_tamagawa: update uart trigger.
samples: SDM: add console to test different function.
samples: dmav2: update dmav2 fixed burst transfer size
samples/components/middleware: use clock_get_core_clock_ticks_per_us() and clock_get_core_clock_ticks_per_ms() instead of hpm_core_clock
samples: lobs: use lobs_signal_group_t and lobs_trace_data_t
samples/middleware/components: add clock to group by applications
samples: i2c: use add board_init_i2c_clock() API
samples: audio sample dependency change
samples: dhrysone: update compile options
samples: i2s: use BOARD_APP_I2S_TX_DATA_LINE instead of BOARD_APP_I2S_DATA_LINE
samples: mcl: bldc_foc: modify clc to use the pid parameter
samples: audio: update codec I2S channel.
samples: lwip: common: single & multiple: eliminate two “Down” status at the first linkup
samples: tsn: all: samples: tsn: all: eliminate two Down status at the first linkup
samples: erpc: update button pressed
samples: cherryusb: use BOARD_BUTTON_PRESSED_VALUE instead of APP_BUTTON_PRESSED_VALUE
samples: spi_components: half duplex: add notice content for all readme
samples: spi_components: fixed compile waring on SES for half duplex slave dma sample
samples: drivers: tsw: add phy reset logic
samples: lwip: lwip_iperf_multi_ports: app.yaml: update excluded target list
samples: ecat_io: update DC setting in README
samples: tflm: optimized speed.
samples: i2s: change HDMA to XDMA
samples: plb: pulseoutput: rename init_plb_pins() to init_plb_pulse_pins()
samples: ecat: support initializing eeprom data.
samples: lwip: mhd_wifi_demo optimize TCP RX and UDP RX performance.
samples: lwip_tcpclient_freertos_socket: eliminate the use of the global variable gnetif
samples: ppi: sram: update as/ah stage time
samples: cherryusb: adapter to cherryusb v1.4.2
samples: pwm: add pwm duty 0-100 output
samples: lwip: mhd_wifi_demo update limitation.
samples: lwip: mhd_wifi_demo add limitation for andes&zcc toolchain.
samples: tsn: tsn_psfp_egress: adjust some settings.
utils: hpm_swap: exclude bswapxx for segger_rtl
docs: add plb filter doc to index
docs: samples: drivers: mipi_csi: update the project setting configuration
cmake: toolchain: update RV_ABI for nds-gcc, when it’s not set
Fixed:
isr: adjust SDK_DECLARE_EXT_ISR_x position to fix clang warning
soc: irq s mode: fix CONFIG_RTTHREAD lost
soc: hpm6e00: ip: tsw: fix the access attributes of TXDATA/TSYN_TXBUF_TQUE_AND_TX_LEN in BIN
soc: linker: add “*” to some sections
soc: modify register used by DSP in IRQ nesting, from s0 to s4 .
soc: modify interrupt handler under vector mode
soc: add section .isr_vector.*
soc: fix freertos vectormode build error
soc: hpm6e00: fix the register offset in cb frer module
soc: reset.c: weak __dso_handle
soc: HPM6700: HPM6750: acmp: fix missing a dependent clock setting.
soc: HPM6E00: fix TRGM register header file
drivers: pdgo: fix incorrect register accessing
drivers: sdm: remove useless function and add new API.
drivers: hpm_enc_pos_drv: fix build warning when -Werror=double-promotion
drivers: i2c: fixed data length assignment error for i2c_master_address_read API
drivers: sdxc enable adma3 support.
drivers: tsw: add the missing doxygen description for the return value from tsw_shap_set_cbs
drivers: tsw: fix no update trigger in tsw_get_rtc_offset
drivers: tsw: fix missing the higher part of second in tsw_set_rtc_offset
drivers: femc: update sram default config
drivers: femc: support sdram1 and sram1/2 config
drivers: vsc: fix sw only inject adc value don’t trigger vd/vq calculation
drivers: plb: fix enum plb_type_a_lut_num
drivers: trgm: fix trgm_filter_mode_stable_high and trgm_filter_mode_stable_low
drivers: fix error status checking in esc_phy API
drivers: tsw: fix compile warning with andes toolchain
drivers: pla: fix pla comment.
drivers: pwmv2: fix pwmv2 driver code error.
drivers: pwmv2: disable pwm forced output by default.
drivers: sdm: fix API to avoid configuring wrong register value if multiple calls.
drivers: set ewdg window mode timeout to 101ms.
drivers: sdxc correct typo in sdxc status code.
drivers: canopen fix can related boards iar build error.
drivers: tsw: fix failing to control gate to close in static mode.
drivers: tsw: fix size filtering for psfp setting.
drivers: acmp: fix using a fixed acmp clock source name.
drivers: mcan fix typo in mcan driver.
components: serial_nor: fixed the issue of address and data phase assignment error when parsing the read instruction parameters of SFDP
components: plb_lin_clock: change variable types to avoid overflow.
components: enet_phy: jl1111: fix register address info.
components: spi: due to divide by 2, the SPI frequency division is allowed to be 0 for hpm_spi_set_sclk_frequency API
boards: fix core1 don’t init hpm_core_clock
boards: hpm6800evk:: fixed the GPTMR COMP position error for readme
boards: hpm6750evkmini: fix touch reset timing.
boards: sdram: add and use macro BOARD_SDRAM_COLUMN_ADDR_BITS
boards: hpm6750evk2/hpm6300evk: change init_sdram_pins() to init_femc_pins()
boards: hpm6750evkmini: remove ETH0_EVTO_2/ETH0_EVTI_2 pin setting
boards: enet: fix missing clock source setting for RGMII port
boards: fix RGB pin pad setting.
boards: hpm6e00evk: correct uart_lin pin setting
boards: hpm5301evklite: pinmux: change the same of init_gptmr_pins API pin for init_gptmr_channel_pin API
boards: hpm6200evk: set cpu clock using pll1clk1, avoid impact pll1clk0
boards: hpm6800evk: set dcdcm work mode to 1
boards: board_sd_configure_clock fix clock unstable issue during transition.
boards: hpm6300/hpm6700/hpm6800: fix BOARD_BUTTON_PRESSED_VALUE error
boards: fix missing board-level acmp clock setting API.
boards：openocd: hpm6300evk.cfg: correct delay cell setting
boards: openocd: fix openocd access non-standard csr problem
boards: hpm6200evk: fix BOARD_CPU_FREQ value
middleware: add canopen v2.0 support.
middleware: improve freeRTOS vector mode isr efficiency
middleware: fix segger compile error
middleware: vglite: fix build error
middleware: optimize threadx related CMakeLists
middleware: optimize uC/OS-III related CMakeLists
middleware: optimize FreeRTOS related CMakeLists
middleware: fix ucos_iii core1 error
middleware: fix .align error in s files
middleware: hpm_mclv2: preventing divide-by-zero errors in alpha beta.
middleware: hpm_mclv2: Fixing the motor with many pole pairs at the wrong angle.
middleware: lwip: opt.h: recover LWIP_TCPIP_CORE_LOCKING setting to 1
middleware: hpm_sdmmc: spi sdcard: fix spi sdcard log redirection definition error issue
middleware: rtthread-nano finsh rx add receiving buffer .
middleware: lvgl: fix large screen logo incorrect
middleware: put function into section isr_vector
middleware: hpm_mcl_v2: fix calls can lead to illegal pointer accesses.
middleware: rtthread-nano,delete print wrapper.
middleware: mbedtls: port: fix the logic of sourcing sdp files when there’s no sdp on the specified soc
middleware: fix trace_recorder rtt error
middleware: rtthread-nano,fix thread detach not schedule.
middleware: rtthread-nano,modify console marco dependency.
middleware: rtthread-nano add declaration in interrupt.S.
middleware: fix trace recorder IAR build error
middleware: hpm_sdmmc fix errors reported by clang-tidy.
middleware: hpm_sdmmc: hpm_sdmmc_sd Fix logic issue for getting card flag and read last sector.
middleware: hpm_mcl_v2: Fix wrong sector number.
middleware: hpm_sdmmc ensure the ADMA3 table is 8-byte aligned.
samples: multicore_hello: change core1 demo from pwm to gptmr.
samples: rgb_led: use pwmv2 to support led control.
samples: rom_api: xpi_nor_api correct the read_status instruction seq.
samples: usb: fix segger compile error
samples: i2c_components: add initialize the i2c clock
samples: i2c_components: rename the cmakelists file to CMakeLists
samples: uart_lin_salve: add board lin transceiver control.
samples: drivers: gpio: Fixed the problem of not working properly on both edge trigger mode
samples: tinyusb/usbx: host: fix build warning
samples: tsn: tsn_time_aware_scheduling: fix comment error
samples: lwip: common: multiple: fix compiling error with zcc toolchain
samples: femc: sram: use macro BOARD_FEMC_ASYNC_SRAM_AD_MUX_MODE and BOARD_FEMC_ASYNC_SRAM_SIZE
samples: femc: sram: use macro BOARD_FEMC_ASYNC_SRAM_CS_INDEX
samples: update section .fast_ram to .fast_ram.non_init and .noncacheable to .noncacheable.non_init
samples: lwip: fix the comment for ICMP checksum
samples: lvgl_audio_player: fix build error for update lvgl v9.2
samples: lvgl: rtos: fix compilation error for using RECURSIVE_MUTEXES in lvgl.
samples: spi_components: half_duplex: dma: for master, Need to determine SPI transmission completion when send
samples: pmbus: change SMBUS related macro definitions to PMBUS
samples: drivers: gptmr: timer_basic: fixed the issue the time information was not printed
samples: drivers: pllctlv2 Correct UART buadrate after preset switching.
samples: drivers: pllctl Avoid access to FLASH during clock transition.
samples: motor_ctrl: bldc_lvgl: fix compiler error
samples: lwip: ports: rtthread-nano: multiple: arch: sys_arch.c: fix that value stored to ‘ret’ is never read
samples: lwip_tcpecho_multi_ports_rtthread-nano: tcp_echo.c: fix that valued stored is never read
samples: motor_ctrl: use pwmv2_issue_shadow_register_lock_event.
samples: rdc: fix rdc desynchronization causing accuracy errors.
samples: lwip: mhd_wifi_demo fix zcc compiling error.
samples: drivers: pllctl force XTAL on in case RC24M is not trimmed.
samples: rtthread rvbacktrace tshell thread stack overflow under zcc.
samples: rvbacktrace, add volatile keyword to prevent optimization.
samples: opener/motor: set motor speed to zero at start
samples: fix multicore/erpc/motor project link error
samples: enable gptmr clock in OpENer/motor sample
samples: disable dhcp in sntp sample by default
samples: mbedtls: fix program exception blocking
samples: lwip_https_server: fix function error
samples: separate rev and pos data in 53xx soc
samples: rom_api: xpi_nor_api place flash API into RAM.
samples: modbus: tcp: fix lwip init warning for IAR build type
samples: add some info to trace recorder samples
samples: pwmv2: fix one clock cycle of pulses at startup.
samples: spi_sdcard: add SPI transfer completion judgment for DMA transmission
samples: enet: pps: fix no output
samples: jpeg_decode: fix extract jpeg head failed
samples: lwip_tcpecho_multi_ports_rtthread-nano: fix DHCP failure
samples: bldc_foc: fix speed loop parameters.
samples: image: fix udisk build failure
samples: tsn: tsn_credit_based_shaper: fix getting phy link status logic
samples: qeo_dac: add dac clock enable in sample.
samples: uart lin slave buadrate adaptive fix readme.
samples: drivers: dma: dma_use_gptmr_event_transfer: adjust the clock_add_to_group API call order for gptmr
samples: plb doc: index change to glob
samples: ecat_foe/ecat_cia402 add missing macro.
samples: ecat: rename eeprom_update image file
samples: fix canopen release type PDO block.
samples: canopen add to sample list.
samples: exclude OpENer motor sample from hpm6750evk2 and hpm6300evk
samples: motor_ctrl: motor running noise.
samples: i2s_emulation: fixed the abnormal playback issue if there is no recorded content
samples: rom_api: xpi_nor_api Fix crashing when using zcc toolchain.
samples: usbx: msc: fix doc description error
samples: cdc_acm_uart_com: fix readme max baudrate description
samples: tsn: fix log format for RX-Time.
samples: tsn: tsn_frame_preemption_egress: fix FPE indication value error.
samples: tsn: frame_preemption_ingress: fix that eth smac doesn’t match with arp smac.
samples: tsn: tsn_frame_preemption_ingress: fix that the preemption logic is not expected with flash_sdram_xip in release configuration.
samples: lwip_tcpecho_multi_ports_rtthread-nano: fix the main thread stack overflow with the zcc toolchain
samples: plic button sometimes does not work.
samples: fix trace recorder doc
samples: exclude unsupported sample
samples: image: encoder: fix encoder flow
samples: uart_tamagawa: change hardware trig way
samples: fix compilation error related to struct timeval with andesight toolchain
samples: motor_ctrl: bldc_offline_param: Fixing Printing Information Errors.
samples: motor_ctrl: Fixing speed switching causing motor stalling
samples: SEI: add missing clear interrupt flag code
docs: readme: fix plb pin descriptor
docs: get_started: replace hpm6750evk with hpm6750evkmini
docs: rvbacktrace, add rvbacktrace docstree to the sample docstree.
docs: add motor related information in readme
docs: rdc: Add description of initial position.
docs: hpm6e00evk: fix plb filter pins descriptor
Added:
soc: add clock_get_core_clock_ticks_per_us() and clock_get_core_clock_ticks_per_ms() APIs
soc: clock driver add clock_wait_source_stable API.
drivers: i2c: add i2c_set_direction API
drivers: i2c: add enable and disable stop phase APIs for master
drivers: i2c: add enable and disable data phase APIs for master
drivers: i2c: add enable and disable address phase APIs for master
drivers: i2c: add enable and disable start phase APIs for master
drivers: i2c: add i2c_master_set_slave_address API
drivers: i2c: add i2c_master_issue_data_transmission API
drivers: i2c: add i2c_set_data_count API
drivers: i2s: add i2s_config_multiline_transfer() API
drivers: sdxc add api for interrupt_signal retrieval.
drivers: adc12: fix using a wrong calibration value
drivers: ffa: add long data support.
drivers: qeiv2: add qeiv2_config_phmax() and qeiv2_config_phparam() APIs
drivers: sdm: add new feature GATE/Timestamp API.
components: add i2c component
components: enet_phy: add enum enet_phy_link_unknown in enet_phy_link_status_t
components: spi: add the spi slave is not support QSPI and DSPI judgment
components: add plb filter component
components: add plb lin clock detection.
boards: add macro BOARD_BUTTON_PRESSED_VALUE
boards: hpm6750evk2: pinmux: fix build warning in init_sdxc_clk_data_pins() with zcc toolchain
middleware: hpm_sdmmc add sdio support.
middleware: modify rvbacktrace resources file.
middleware: add RvBacktrace resources.
middleware: add trace recorder rtthread support
middleware: add trace recorder support
middleware: add uC/OS-III gptmr support
middleware: usb: add macro CONFIG_USB_DEVICE_FORCE_FULL_SPEED instead of CONFIG_USB_DEVICE_FS
middleware: usb: add macro CONFIG_USB_HOST_FORCE_FULL_SPEED to force usb host working in full speed
middleware: add OpENer support
middleware: fatfs: sdxc add support for interrupt-driven mode.
middleware: hpm_sdmmc add support for interrupt-driven mode and osal.
middleware: hpm_mcl: add 3p3z convert pid function.
middleware: wifi add the MHD wifi stack.
samples: add rtthread rvbacktrace under using fp register.
samples: add baremetal rvbacktrace under no using fp.
samples: add baremetal rvbacktrace using fp.
samples: add info to OpENer samples’s doc
samples: add rtthread trace recorder sample
samples: add trace recorder freertos sample
samples: add uC/OS-III hello world using gptmr as systick source
samples: add master and slave samples for i2c dma components
samples: add master and slave samples for i2c polling components
samples: add OpEner multicore motor control
samples: add OpEner motor control
samples: add OpENer blinky
samples: spi_components: slave: add notice content for all slave samples readme doc
samples: drivers: spi: add notice content for all spi slave readme doc
samples: sdxc add support for interrupt-driven mode.
samples: lwip: add conditional compilation for application macros
samples: lwip: add a lwip_udpecho_freertos_socket sample
samples: lwip: add a lwip_udpecho_rtthread-nano
samples: lwip: add a lwip_udpecho_freertos sample
samples: lwip: add a lwip_udpecho
samples: lwip: lwip_tcpclient_freertos_socket: add a macro name of task priority for netif_update_link_status
samples: lwip: lwip_tcpecho_freertos_socket: add a macro name of task priority for netif_update_link_status
samples: cherryusb: add cdc acm host sample
samples: motor_ctrl: bldc_xxx & step_motor_foc: add missing diff_sel passed into adc12_init
samples: ethercat: ecat_cia402: motor: bldc_foc: add missing diff_sel passed into adc12_init
samples: drivers: adc: adc12: add missing diff_sel passed into adc12_int
samples: tsn: tsn_ethernet: lwip_tcpecho: add interrupt usage
samples: plb: add plb filter sample
samples: optimize demo current loop time.
samples: lwip: mhd_wifi_demo add wifi demo for ap6256.
samples: add uart lin slave buadrate adaptive samples.
samples: cherryusb: add uvc demo
samples: lwip: common: single: add an API for getting the DHCP ready staus when enabling DHCP
samples: lwip: add a lwip_ping_freertos_socket sample
samples: tsn: add tsn_psfp_egress
samples: tsn: add tsn_stmid_frer_ingress
samples: tsn: add tsn_stmid_frer_egress
samples: tsn: add tsn_frame_preeemption_ingress
samples: tsn: add tsn_frame_preemption_egress
[1.7.0] - 2024-09-30:
Main changes since 1.6.0
Tested Segger Embedded Studio Version: 8.16a
Tested Zcc toolchain 3.2.4
Changed:
soc: HPM6E00: HPM6E80: add tsw section
soc: add hpm_otp_table.h
soc: enet: add a macro for DMA bus width
soc: system.c: set bpor.por_confing retention bit to avoid bgpr data loss
soc: pcfg: add pcfg_wakeup_src_t enum and pcfg_update_periph_clock_mode API
soc: hpm5300: exclude fgpio region from dlm
soc: add CONFIG_ENABLE_BPOR_RETENTION macro to control bpor retention
soc: linker: icf: update cherryusb_usbh_class_info section placement
soc: HPM6300/HPM6700: delete pcfg_dcdc_set_current_hys_range() API
ip: i2s: add and use clk_i2s_src_audn instead of clk_i2s_src_aud0/1/2/3
boards: remove hpm6750evk support
boards: hpm6e00evk: update femc pinmux
boards: pinmux: set max frequency slew rate for SPI GPIO
boards: hpm5301evklite: Change cap1 and comp1 pins of gptmr0
boards: hpm5301evklite: change i2c2 to i2c3 for BOARD_APP_I2C
boards: add board_init_gptmr_channel_pin API for all board
boards: hpm6e00evk: update core1 debugger console readme
boards: all: add board_init_acmp_pins API
boards: hpm6800evk: adc16: update clock bus name for clock initialization
boards: adc16: rename api parameter clk_src_ahb to clk_src_bus
boards: add BOARD_APP_ADC16_CLK_BUS definition
boards: hpm6e00evk: update board readme
boards: hpm6e00evk: bump up DCDC voltage to 1250mv
boards: add enet pps input feature and pinmux setting API
boards: add missing board feature and pin descriptions for enet pps output pin
boards: xxxx.yaml: rename board feature name related to enet pps pin
boards: add BOARD_MASTER_I2S and BOARD_SLAVE_I2S
boards: add board mic and speaker i2s definition
boards: doc: pwm: add pwm pin descriptions.
boards: hpm6800evk reduce ddr io leakage.
boards: hpm6800evk: pps: adjust pinmux settings
drivers: tsw: optimize the logic of sending and receiving APIs
drivers: tsw: add APIs for speed, interface, and clock delay settings
drivers: tsw: split tsw_ep_enable_mac_ctrl API to two APIs for enableing and disabling
drivers: usb: update usb phy init for suspend
drivers: qeiv2: update comments
drivers: i2c: auto ack needs to be enabled after the transmission is completed for i2c_master_transfer API
drivers: adc16: split adc16_set_pmt_queue_enable() into enable and disable API
drivers: gptmr: add opmode cntmode monitor configuration member for gptmr_channel_config API
drivers: spi: add the judgment that the frequency ratio cannot be greater than 510 for spi_master_timing_init API
drivers: enet: add retry logic in DMA initialization
drivers: spi: Add slave mode judgment for spi_control_init API
drivers: spi: add spi busy state judement for transfer APIs
drivers: uart: add disable rx timeout trigger dma function
drivers: i2s: add buff data align with frame feature
drivers: acmp: add acmp_channel_config_cap_selection
drivers: acmp: update acmp_channel_config_dac API
drivers: usb: update usb phy init and deinit
drivers: enet: add auxiliary snapshot APIs and struct definitions
drivers: usb: update usb_force_port_resume() annd add usb_hcd_disable_ase_pse() APIs
drivers: tsw: update the prefix of apis starting with tsn to tsw
drivers: qeiv2: update qeiv2_config_adcx_adcy_param()
drivers: usb: update usb_hcd_disable_ase_pse() & usb_hcd_enable_ase_pse()
components: enet_phy: rtl8211: optimize logic for initialization config
components: ppi: add assert check for cs_index and cmd_start_index
components: ppi: update AD-MUX mode config to decrease address latch
components: smbus: i2c_master_write replaces i2c_master_transfer for all smbus write APIs
components: serial_nor: Added configuration return judgment for transfer API
components: serial_nor: judge DMA sending completion for hpm_spi_transfer_via_dma API
components: spi: add spi busy state judgment for hpm_spi_transfer_init API
components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_buffer_nonblocking API
components: i2s_over_spi: optimized hpm_i2s_master_over_spi_tx_stop API
components: i2s_over_spi: add hpm_i2s_master_over_spi_tx_is_busy API
middleware: hpm_math: support zcc new version
middleware: cherryusb: update to v1.4.0
middleware: lwip: CMakeLists.txt: add cmake flag for apps
middleware: cherryusb: don’t clean csc bit when init
middleware: cherryusb: msc host: support multi msc device
middleware: fatfs: cherryusb: support two msc device
middleware: reduce netx mem usage
middleware: cherryusb: host: update usb_hc_deinit()
middleware: usbx: host: delete mode setting in usb_host_mode_init()
middleware: hpm_sdmmc: sdcard: added retransmission to improve SPI SD card compatibility
middleware: tinyengine: rename old function
samples: audio_codec: change default codec setting in CMakeLists.txt
samples: adc16 & motor_ctrl: update adc16 preemption queue enable control APIs
samples: ppi: parallel_adc: update function name
samples: ppi: async_sram: update to support AD Mux Mode
samples: lwip & modbus: add judgement for the return value of enet controller initialization
samples: lwip: lwip_iperf: exclude flahsh_uf2 & flash_uf2_release targets
samples: lwip: add conditional compilation for RMII port
samples: cherryusb: msc host: adapter to fatfs update
samples: drivers: acmp: replace init_acmp_pins API with board_init_acmp_pins API
samples: ecat: read mailbox ram buff by ram alias address
samples: ecat: set PHY offset
samples: ecat_phy: disable PHY addr 00 broadcast response
samples: drivers: adc16: reference APP_ADC16_CLOCK_BUS instead of clk_adc_src_ahb0
samples: ecat_io: update flash_eeprom data address
samples: ecat: update SSC config xml and ESI xml
samples: lwip: ports: rtthread-nano: single&multiple: add sys_arch_protech()/sys_arch_unprotect()
samples: power_mode_switch: move sysctl_enable_cpu0_wakeup_source_with_irq() to stop mode settings
samples: power_mode_switch: keep puart clock and wakeup enable visible
samples: acmp: add a macro TEST_ACMP_DAC_MAX_VALUE for better compatibility
samples: drivers: enet: pps: app.yaml: rename dependency
samples: ppi: parallel_adc: use macro BOARD_PPI_ADC_CS_INDEX
samples: i2s: use BOARD_MASTER_I2S and BOARD_SLAVE_I2S
samples: audio_codec: use board speaker macros
samples: cherryusb: audio: use board mic and speaker macros
samples: lwip & cherryusb/host/usbnet: use the external struct timeval definition from compile system
samples: esc: update esc read to 32bit access
samples: ecat_foe: update log and README
samples: ecat_foe: foe flash read cache maintenance
samples: ppi: use macros to select pins
samples: drivers: gptmr: cntmode: volatile to key parameter variables to prevent them from being optimized
samples: spi_sdcard: Added delay function registration
samples: cherryusb: mouse_wakeup: update printf log
samples: cherryusb: midi: update readme
samples: i2s: change HDMA to XDMA
samples: tflm: optimized speed.
samples: tflm: add zcc compile options.
samples: spi_component: full_duplex: Add known issues in the master readme
samples: spi_components: half_duplex: reduce SPI SCLK frequency to adapt to different slave boards
samples: spi_components: full_duplex: reduce SPI SCLK frequency to adapt to different slave boards
Fixed:
soc: HPM6800: HPM6880: fix the clock bus name for wdg
soc: SPI_SOC_TRANSFER_COUNT_MAX Definition error for HPM6E00
soc: preserve kept symbols while -flto is enabled
soc: hpm6880: fix clk bus name for adc from ahb0 to axis0
soc: HPM6300: fix get get_frequency_for_i2s_or_adc() problem
soc: HPM6700: fix clock_set_i2s_source() check condition
soc: romapi: Fix unexpected data fetch error during flash init/write.
soc: linker: gcc: fix fast_ram postion
boards: hpm5301evklite: add a missing macro BOARD_APP_ADC16_CLK_BUS
boards: i2c init: clock_add_to_group() should be before board_i2c_bus_clear()
boards: hpm6800evk pinmux PRS set wrong value
boards: hpm6750evkmini: fixed the iomux errata causes the slave to not work issue
boards: hpm6750evk2: fixed the iomux errata causes the slave to not work issue
boards: hpm6750evkmini: add the missing implement of enabling enet irq
boards: hpm6750evkmini: fix touch reset timing.
drivers: i2c: correct API name
drivers: gptmr: fix cmp value can’t set 0xFFFFFFFF problem
drivers: pwmv2: fix counter burst set error.
drivers: enet: fix return value of enet_dma_init()
drivers: usb: fix usb_dcd_remote_wakeup() api
drivers: enet: fix enet max frame size
drivers: spi: Fixed mode variable assignment error for spi_slave_get_default_format_config API
drivers: i2s: fix fill dummy data in slave mode
drivers: adc16: fix ADC16 conversion results in single-ended mode
drivers: enet: fix that TSIS interrupt is disabled by default
drivers: femc: fix cmd_data_width comment error
drivers: spi: fixed offset digit error problem for spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
drivers: spi: fixed possible packet loss during reception for spi_read_data API
drivers: usb: fix phy init for host
drivers: touch: gtxx: fix reset timing
drivers: mipi dsi: fix bandwidth low
drivers: mcan: fix wrong offset in can_rx_message_t.
drivers: adc12: fix using a wrong calibration value
components: ppi: fix config variable init value
components: serial_nor: Fixed the nonblock APIs naming error
components: serial_nor: spi: fixed formating issue for write API
components: eeprom_emulation, add “fence.i” after nor_flash init
components: spi: fixed the waring of no return value for hpm_spi_transfer_init API
middleware: fix Nan calculation error.
middleware: lwip: apps: lwiperf: fix the type of clk_id from int to clockid_t
middleware: fix tickless mode cannot work
middleware: eclipse_threadx: netxduo: fix confilicting types for ‘enet_mask_interrupt_event’
middleware: tinyengine: zcc compile error.
middleware: cherryusb: fix msc class miss return
middleware: motor_monitor: fix nds toolchain error
middleware: hpm_mcl: pwm output exception.
samples: sdm: correct gptmr trigger time
samples: gptmr: cmp0 and cmp1 should be setting together
samples: i2s_emulation: fixed playback is not actually stopped issue
samples: pwmv2: fix pwm period error.
samples: drivers: dac: fix output stop after restart in buffer mode
samples: fatfs: fix driver_num_buf don’t have EOF
samples: dac: buffer mode: fix DAC output of negative narrow pulse nearly to zero at the top of sinewave
samples: lwip: fix enet receive buffer size setting
samples: lwip: fix some memroy-related issues when using socket/netcon API
samples: cherryusb: audio: fix mute problem when audio open
samples: power_mode_switch: fix hpm62xx/63xx/67xx into shutdown mode can’t be woke up
samples: i2s: fix pdm record data buff size according board
samples: lwip_ptp: v1 & v2: fix compiling error with gnu gcc toochain in v13.0
samples: i2s_emulation: fixed build error for nds gcc
samples: drivers: spi: interrupt: Abnormal working for IAR release build
samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
samples: drivers: spi: dma: master: fixed can not work sometimes with release build issue
samples: i2s_emulation: fixed can not stop when playing issue
samples: drivers: gptmr: opmode: fixed can not work with release build type
samples: dsp: Calculation error in dsp demo.
samples: lwip: lwip_ptp_v2: fix function error with flash_sdram_xip_release
samples: drivers: uart: uart_hardware_rx_idle: fiexd can not work with zcc release build type
samples: bldc offline detection: fix release run error.
samples: mono: fix value get logic on zcc.
samples: fix sample slave tamagawa’s trx error handling method
samples: ecat: fix build ZCC error
samples: lower power: hpm6300 and hpm6700 can’t use pcfg_dcdc_set_current_hys_range() API
cmake: ide: correct glob source adding
cmake: zcc: correct arch setting to enable dsp
scripts: add errors=ignore and encode=utf8 parameters to avoid python unicode build error.
samples: motor_ctrl: bldc_xxx & step_motor_foc: add missing diff_sel passed into adc12_init()
samples: ethercat: ecat_cia402: motor: bldc_foc: add missing diff_sel passed into adc12_init()
samples: drivers: adc: adc12: add missing diff_sel passed into adc12_int()
doc: fix threadx doc title
Added:
soc: HPM6300: add pps1_en
drivers: add hrpwm recovery method.
drivers: trgmux: add hrpwm calibration driver.
drivers: sei: add sei_set_dma_req_enable() API
drivers: ppi: add and use ppi_ns2cycle() API
drivers: i2c: add I2C_WRITE_CHECK_ACK flag for i2c_master_transfer API
drivers: i2c: add i2c_master_seq_transmit API
drivers: plb: add new plb interface
drivers: tsw: add tas, cbs and pps APIs
drivers: tsw: add tx-timestamp-fifo APIs
components: tsw_phy add RTL8211 and JL1111 drivers
components: add pmbus
components: ppi: add README.md docs
components: add plb abz encoder.
middleware: add hpmicro monitor.
middleware: motor_ctrl: add motor parameter detection.
middleware: add tsn
samples: tsn: add lwip_tcpecho
samples: bldc_foc: add motor monitor demo.
samples: motor_ctrl: add bldc parameter detection demo.
samples: drivers: pwmv2: add hrpwm calibration demo.
samples: cherryusb: add mouse remote wakeup sample
samples: gptmr: add opmode/monitor/cntmode sample
samples: add pmbus samples
samples: cherryusb: dual_host: support two msc device
samples: ecat: add ecat_foe samples
samples: ecat: add ecat_cia402 samples
samples: ecat: add ecat_foe driver
samples: ecat: update hpm_ecat_hw driver
samples: drivers: enet: add pps_capture sample
samples: add plb encoder demo.
samples: tsn: add tsn_time_aware_scheduling
samples: tsn: add tsn_ptp_freertos(master&slave)
samples: tsn: add tsn_credit_based_shaper
samples：ecat_cia402: add virtual motor support
[1.6.0] - 2024-06-28:
Main changes since 1.5.0
Tested Segger Embedded Studio Version: 8.10d
Tested IAR Embedded Workbench for RISC-V Version: 3.30.1
Known Issue:
some IAR projects does not work properly when optimization level is increased
Changed:
soc: reorganize the directory structure
soc: hpm6750: declare get_frequency_for_source API for clock drver header file
soc: update soc cmakelists to add b ext info
soc: hpm6750: add feature for ioc pad ctrl setting issue
soc: toolchains: gcc: correct LMA for NOLOAD sections
soc: move eh_frame into separate section
boards: hpm6750xxxx apply workaround for E00029.
boards: change hpm5301evklite adc16 channel
boards: board.h: adc16: add marco BOARD_APP_ADC16_HW_TRIG_SRC_CLK_NAME
boards: adjust function position of adc pin initialization
boards: hpm6300evk and hpm6e00evk: sdram use px07 as femc dqs pin
boards: hpm6e00evk: rename init_sdram_pins to init_femc_pins
boards: hpm6e00evk: change board i2c instance to I2C0
drivers: can/mcan add parameter check for low-level bit timing.
drivers: enet: add bitfield ENET0_RMII_TXCLK_SEL for hpm6300
drivers: i2c: add DATACNT high byte process
drivers: pwm: update HRPWM process
drivers: spi: optimize reading speed for spi_read_data API
drivers: spi: add set/get data phase format APIs for spi master
drivers: spi: delete the spi startand operation APIs
drivers: adc16: remove an unused member conv_duration from adc16_config_t
drivers: enet: update for enet_interrupt_enable_t
drivers: mcan reduce unnecessary register access in mcan_read_rxfifo.
drivers: mtg: add calculate function param clock
drivers: mtg: add several calculate functions
drivers: mcan lookeup the mcan msg ram base via mcan_soc_msg_buf variable if the MSG_BUF is in AHB RAM.
drivers: adc16: disable improvement logic of adc16 for continuous sampling maximum voltage
drivers: mcan improve transmitter delay compensation setting logic.
drivers: femc: rename data_width_in_byte to cmd_data_width
drivers: femc: update ns2cycle() to align up
drivers: common: add packed attribute
drivers: femc: delete duplicate config
drivers: mtg: change the default parameters to the low order filter
drivers: adc16: add API adc16_set_seq_hw_trigger_enable()
drivers: spi : convert enumeration return in that gets parameters APIs
drivers: pwm: add fault recovery code.
driver: pwm: change pwm trig time
components: enet_phy: dp83867/rtl8211: move the macro definition RGMII to board-level CMakeLists.txt
components: eeprom_emulation: Add ATTR_RAMFUNC for all function
components: eeprom_emulation: add power-off protection mechanism.
components: dma_mgr: add burst in fixed transfer size and swap feature
components: spi: add full_duplex and half_duplex operating APIs
components: spi: support 1 to 32 bits width transfer for nonblocking APIs
components: usb: device: support iso transfer mult feature
middleware: hpm_sdmmc add emmc sleep & wakeup function.
middleware: tinyusb: ehci: support chain transfer
middleware: threadx: add low power support
middleware: cherryusb: update for advance descriptor
middleware: hpm_sdmmc: optimized to support multiple cards
middleware: cherryusb/tinyusb/usbx: enable suspend isr
middleware: FreeRTOS: update to 202210.01 lts
middleware: cherryusb: update to v1.3.0
middleware: freertos: modify missed timer count num
middleware: freertos: update IAR port file
middleware: freertos: delete fence operations
middleware: freertos: make the calculation more simple.
middleware: hpm_sdmmc add cache control macro.
middleware: hpm_sdmmc: improve the logic for detecting CMD23 support.
middleware: freertos: add tickless stop mode support
middleware: freertos: add user custom process function call
middleware: hpm_mcl_v2: add hpm smc control.
middleware: freertos: place xPortxxx to isr_vector section
middleware: hpm_math: add dsp support for zcc
middleware: microros: add zcc support
middleware: rtos: asm adjustment for zcc toolchain
middleware: hpm_mcl_v2: add pwm dead area compensation.
middleware: hpm_mcl_v2: add dq axis decoupling function
middleware: cherryusb: add macro USBH_USE_CUSTOM_ISR/USBD_USE_CUSTOM_ISR
middleware: lvgl: upgrade to v9
middleware: lvgl: rewrite the scissor.
middleware: lvgl: upgrade allocate algorithm for draw_buf.
samples: rdc: remove unused dac driver in sample
samples: lwip/netxduo/modbus: add conditional compile for reference clock setting in RMII mode
samples: audio_codec: common: change FIL_SEARCH_NUM from 10 to 20
samples: dhyrstone: surpress build warnings
samples: dhrystone Optimize performance.
samples: coremark Optimize performance.
samples: drivers: spi: interrupt: transmission optimization. The transmission will start after the configuration is completed.
samples: adapt spi components to drive and move to the samples dir for spi sdcard samples
samples: cherryusb: device: change descriptor string to HPMicro
samples: cherryusb: device: use advanced descriptor to support high/full speed
samples: rename jpeg to image
samples: drivers: sdxc: sd_fatfs: add card hotplug support
samples: cherryusb: host: usbnet: replace block to noblock for read terminal char
samples: cherryusb: host: usbnet: decrease lwip MEM_SIZE
samples: cherryusb: move host hid info print code to thread
samples: audio_codec: refactoring code
samples: spi: dma: SPI master transmission optimization
samples: mtg: make the open_loop_trajectory sample more readable
samples: drivers: adc16: add some misc optimization
samples: drivers: adc16: add pwmv2 support
samples: motor_ctrl: bldc_foc_hw: remove hardware control
samples: drivers: mcan add tips for the usage of tdc.
samples: vglite: update rtos config file to fit gptmr tickless mode
samples: lwip/modus/netxduo: add a function call to get the enet default interrupt config
samples: sdm: using pwm to provide clock for sdm sensor.
samples: spi_components: half_duplex: updated to support 1 to 32bits width transfer
samples: spi_components: full_duplex: updated to support 1 to 32bits width transfer
samples: add freertos tickless stop mode sample
samples: benchmark: update compile options for zcc
samples: drivers: adc16: optimize the process logic of sequence and preemption
samples: drivers: sei: device: tamagawa: update eeprom cmd
samples: adc12: optimization for trigger mux and trigger frequency settings
samples: sei: device: tamagawa: support EEPROM protocol
samples: mcl: add pwm dead area compensation.
samples: motor_ctrl: add dq axis decoupling function
samples: cherryusb: move dual_port samples to dual_port folder
samples: cherryusb: adapter to cherryusb v1.3.0
samples: drivers: adc12/adc16/dac: support abort feature in interactive terminal
samples: lwip: lwip_iperf: support abort feature to reselect the test mode
samples: lwip: common: multiple: add definitions of remote ip addresses for iperf
samples: motor_ctrl: bldc_lvlg_foc: add lvgl v8.3.5 for this demo
samples: tinyusb: uac2: support full speed
samples: power_mode_switch: update readme
samples: cherryusb: uac2: change default samplerate order
samples: bldc_foc: update bldc_foc_angle_align() for hardware loop
cmake: toolchain: add ar option to remove timestamp
cmake: toolchain: suppress output while querying spec
cmake: lld: update link option for zcc
cmake/scripts/soc: support b ext convertion to tools
cmake: sdk_app_src_glob: modify to recursive
Fixed:
soc: update USE_NONVECTOR_MODE defined used
soc: initialize .fast_ram.* section
soc: iar linker: fix safe stack init
soc: add missing ptmr clock
soc: hpm6880: fix get_frequency_for_i2s error
soc: hpm6880: Modify the value of SPI_SOC_FIFO_DEPTH from 4 to 8. for hpm_soc_feature.h
soc: toolchain: iar fix iar ram_stress issue in ram_debug build.
boards: hpm5301evklite: fixed can’t output work for gptmr samples such as pwm_generate
drivers: enet: fix the clearing of DMA PBL setting
drivers: dma: fix dma_clear_transfer_status() API
drivers: sdxc Fix timeout calculation issue and DMA enabling logic.
drivers: adc16: fix the logic of adc16_set_pmt_queue_enable() when the parameter enable is false
drivers: mbox: fix error that BEIE can’t be operated by interface
drivers: spi: fixed assignment value error for spi_set_clock_phase and spi_set_clock_polarity APIs
drivers: lcdc: fix ST and DMA_ST clear api.
drivers: mipi_dsi: fix MIPI_DSI_FMT_RGB565 config.
drivers: spi: fixed assignment error issue for enable/disable address phase APIs
drivers: i2c: fix return value type of i2c_get_data_count()
components: usb device/enet_phy: fix unwanted files in localize folder
components: panle: fix panel timing.
components: eeprom_emulation: demo flash crashed.
middleware: cherryusb: ehci: delete timeout clear before give sem
middleware: uC/OS-III: modify fpu context save&restore
middleware: cherryusb: fix freertos enter/exit critical
middleware: audio_codec: fix hpm_wav_decode() single channel pbuf data
middleware: mclv2: fix andes toolchain compiler error.
middleware: cherryusb: fix ehci_qh_pool init miss busid for v1.3.0
middleware: lwip: apps: lwiperf: fix the bug of failing to restart iperf in TCP/UDP server mode
middleware: tinyusb: fix _usbd_dev.speed error to support full speed
middleware: hpm_mcl_v2: fix uncontrolled after large changes in motor speed.
samples: dhyrstone: fix build issue for release type using nds toolchain
samples: lwip: lwip_tcpclient: fix TCP commnuication error after DHCP enabled
samples: lwip: lwip_tcpclient_freertos_socket: fix connection error before IP assigned from DHCP
samples: correct cmsis_os2/mem_pool project name
samples: multicore: common Fix SDP memcpy blocking issue in ram_build.
samples: lwip: lwip_tcpecho_xxx_rtthread_nano: fix failing to get IP by DHCP serivice
samples: spi_sdcard: fixed the place section name error issue
samples: cherryusb: audio: fix wm8960 codec volume max value
samples: img: jpeg_decode: fix decode when only one qtab exist.
samples: tflm: mlperf: remove unnecessary codes.
samples: fix cherryusb mic no sound error
samples: spi_components: polling: fixed doesn’t work for polling samples
samples: tamagawa: fix delay times is zero.
samples: bldc_foc: fix hardware_foc position loop error
cmake: link ndsgcc itf for application
cmake: localize_sdk: use utf-8 as default encoding
cmake: ide: keep preprocessing definition
Added:
soc: add zcc toolchain support
soc: clock_driver Add clock_set_wdg_source API.
soc: gcc linker: add fast_ram.init section size overflow check
soc: add FreeRTOS vector mode support
soc/board: add HPM6E80 support
drivers: common: add macros for .fast_ram.*
drivers: enet: add an API enet_get_default_interrupt_config
drivers: enet: add MII mode support
drivers: common add api for converting tick to us or ms.
drivers: pllctlv2 add new API to configure PLL.
drivers: uart: add uart_modem_write_rts_pin API
drivers: uart: add get/clear addr match flags APIs such as addr_match, addr_match_idle, data_lost
drivers: add lobs drivers
drivers: usb: add some APIs for low power future usage drivers: spi: add spi_slave_set_user_status API
drivers: usb: add suspend/resume APIs
drivers: usb: add enter/exit lower power suspend APIs
drivers: spi: add read SPI RX/TX FIFO size APIs
drivers: usb: add usb_set_port_test_mode() API
drivers: sdp add new apis.
drivers: mcan add new api for canceling pending transmission.
drivers: mtg: add get&clear event irq interface
drivers: qeiv2: add oneshot mode
drivers: add clc driver
drivers: add vsc driver
drivers: spi: add get/set shift direction APIs
drivers: uart: add an new API uart_try_receive_byte()
drivers: pixelmux: add api that set mipi dsi date type.
drivers: gptmr: add monitor function APIs
drivers: gptmr: add opmode APIs
drivers: gptmr: add qeimode APIs
components: add i2s_over_spi
components: codec: add wm8978
components: enet_phy: add jl1111 driver
components: add ppi components
components: touch: add gt9271 driver.
components: debug_console: add a new API console_try_receive_byte()
middleware: add lodepng
middleware: add minimp3
samples: cherryusb: device: add WinUSB 1.0 and WinUSB 2.0 samples
samples: lwip: add LPI interrupt mask setting
samples: add i2s_emulation sample
samples: lvgl_audio_player: support mp3 decoder
samples: uart: add uart_rx_line_status sample
samples: add half_duplex samples for spi_components
samples: add full_duplex samples for spi_components
samples: drivers: sdxc: emmc add new sameple for eMMC sleep & awake.
samples: drivers: add lobs sample
samples: drivers: spi: sd/sd_fatfs: support DMA transfer
samples: threadx: add low power mode sample
samples: image: add png encoder sample
samples: image: add png decoder sample
samples: audio_codec: add decoder_mp3 sample
samples: ppi: add parallel adc sample
samples: ppi: add async_sram sample
samples: qeov2: add wave_out sample
samples: qeov2: add abz_out sample
samples: pwm: add async fault demo
samples: motor_ctrl: add hardware foc
samples: drivers: pwmv2: add pwmv2 pair waveform
samples: dmav2: add dmav2_fixed_burst_swap sample
samples: qeiv2: add oneshot mode sample
samples: add smix_dao sample.
samples: add ecat_io sample.
samples: cherryusb: add one host and one device dual port sample
samples: add pwm/hrpwm fault mode
samples: lwip: add lwip_iperf_multi_ports
samples: drivers: tsw: add a tsn_switch sample
cmake: add symbol HPM_BUILD_TYPE to specify build type
docs: add generated cmake_intro.rst
docs: getting started: add zcc support related information
[1.5.0] - 2024-03-29:
Main changes since 1.4.0
Tested Segger Embedded Studio Version: 7.32a
Tested IAR Embedded Workbench for RISC-V Version: 3.20.1
Known Issue:
some IAR projects does not work properly when optimization level is increased
Changed:
soc: iomux: update macro prefix in pmic_iomux and batt_iomux.
soc: feature: change usb endpoint max number from 8 to 16
soc: correct svd files and add subpart module list
drivers: usb: change usb_phy_get_line_state() to external function
drivers: qeiv2: update filter length setting
drivers: adc12/adc16: add sanity check for sample cycle
drivers: femc: add delay_cell_disable config option
drivers: i2s: change fifo threshold parameter.
drivers: i2c: replace and use the macro definition of hpm_soc_ip_feature.
drivers: uart: supplementary description of uart_check_status API.
components: enet_phy: lan8720/rtl8201/rtl8211: unify the default config with type bool
components: enet_phy: remove unused included header file
components: enet_phy: rtl8201/rtl8211: update register description
components: dma_mgr: change isr handler from static to public
middleware: tinyusb: host: use echi drivers
middleware: tinyusb: rename CFG_TUSB_HOST_DEVICE_MAX to CFG_TUH_DEVICE_MAX
middleware: tinyusb: update to v0.16
middleware: rtthread-nano: use soc reset_handler and define MAIN_ENTRY as entry
middleware: fatfs: tinyusb: adapter to tinyusb update
middleware: threadx: use TX_TIMER_TICKS_PER_SECOND to config work ticks
middleware: threadx: use samples tx_user.h
middleware: uC/OS-III: enable sw interrupt in OSCtxSw/OSIntCtxSw
middleware: ucos: ports: Added IAR portable layer for ucos.
middleware: cherryusb/azure_rtos: add defined ICCRISCV for iar
middleware: hpm_math: simplify libdsp path.
middleware: cherryusb: update to v1.1.0
middleware: rtthread-nano:halt cpu when exception occur.
middleware: hpm_math: simplify libnn path.
middleware: threadx: move frequently called function to ram.
middleware: tinyusb: change endpoint number from 8 to 16
middleware: usbx: change endpoint number from 8 to 16
middleware: cherryusb: msc device: update to support multi lun and deinit
middleware: eclipse_threadx: update license
middleware: fatfs: tinyusb: add osal_task_delay() when use rtos wait
middleware: tinyusb: update CMakeLists.txt and delete custom osal_task_delay()
middleware: tinyusb: add debounce in port change isr
samples: erpc: add middleware src use middleware CMakeLists.txt
samples: multicore: core1: use board_init_core1() API
samples: multicore: coremark: delete custom reset_handler and use app_main as MAIN_ENTRY
samples: tinyusb: update samples to adapter tinyusb v0.16
samples: usbx: host: delete unused hpm_usb_host.h
samples: usb: delete CONFIG_USB_HOST set
samples: lvgl_coremark: disable freqswitch_btn when coremark running
samples: mono: move to driver directory.
samples: freertos: change configMAX_PRIORITIES from 7 to 32
samples: rtthread: delete unused macro RT_THREAD_PRIORITY_32
samples: cherryusb: usbnet: decrease rtos stack config size
samples: lwip: all: unify logs about IP information
samples: lwip: lwip_https_server: remove an unused file
samples: lwip: all: update DHCP progress logic
samples: lwip: common: remove s_pxNetIf
samples: lwip: adjust the directories of netconf.c/netcof.h
samples: lwip: common: optimize speed for getting IP from DHCP server
samples: lwip: rename common_lwip.c to common.c
samples: lwip: common: adjust the call logic of netif_set_up/netif_set_down
samples: lwip: common: change the time of invoking netif_user_notification
samples: lwip: common: rename user_notification to netif_user_notification
samples: lwip: adjust directory structures to be compatible with single and multiple network ports
samples: use generate_ide_projects for new samples
samples: cherryusb: device: cdc acm: reorganize directory structure
samplse: gptmr: t_shape_accel_decel: modify the source address mode of DMA.
samples: cherryusb: device: change readbuf size from 2048 to CDC_MAX_MPS
samples: drivers: femc: update sdram dqs config
samples: update app.yaml to use ip_feature
samples: drivers: uart: change to app uart
samples: audio_codec: update wm8960 I2S protocol.
samples: drivers: cam: change cam sample to cam_dvp sample.
samples: usbx: device: msc: decrease ram disk size to 16KB
samples: cherryusb: msc device: update to support multi lun
samples: driver: uart_lin: support LIN transceiver on board.
samples: adc: temp: rename temp to adc16_temperature
samples: bldc block: Compatible with both hall and qeiv2 peripherals.
samples: motor_ctrl: Modify the value of pwm reload.
samples: lwip: common: single/multiple: update the size passed into sys_mbox_new()
samples: lwip: common: single/multiple: replace enet_get_link_status with netif_is_link_up
samples: lwip: lwip_https_server: remove unused header file
samples: lwip: rename macro TCP_XXX_PORT
samples: lwip: add cmake flag for netconn/socket api
samples: decode_wav: sd_fafts: update sd_choose_music.
samples: power_mode_switch: maintain xpi0 clock on switching preset
samples: dhrystone Change the optmization level to O3.
samples: tinyusb: hid_generic_inout: delete redundant image
samples: power_mode_switch: hpm67/hpm63: preserve femc clock at wait/stop mode
samples: erpc: core1: use optimization -os
samples: update uart_tamagawa to use software trig if TRGM not exist.
samples: eeprom_emulation: reduce management area
samples: sdxc: use block_size instead of 512
samples: erpc: add -fno-exceptions compile option
samples: tinyusb: disable debug log print
boards: hpm5300evk and hpm6800evk: add delay after USB_PWR Pin init for power stable
boards: hpm6750evkmini: modify gptmr pins.
boards: hpm6200evk: modify gptmr pins.
boards: hpm6200evk: modify the i2c pins.
boards: hpm6750xxx: update sdram dqs config
boards: hpm6800evk:pinmux Increase drive strength for sdxc pins
boards: iomux: update macro prefix for pmic_iomux and batt_iomux.
boards: rename board feature
boards: update BOARD_APP_UART definition
boards: rename console definitions
boards: hpm5301evklite: update uart clock in board.c.
boards: hpm6750evkmini: change BOARD_GPTMR_PWM_DMA_SRC definition.
docs: samples: use glob in high level readme.
docs: update top level readme.
docs: netxduo: update sntp readme.
docs: threadx: update threadx hello readme.
docs: lwip: align pictures to the left
docs: pip: add cmake doc dependency
docs: add changelog to sphnix-doc.
scripts: ses: generate asm after build by default.
scripts: update linked project path logic.
scripts: check_board_cap.py: check ip feature’s availability
cmake: remove CMP0116 setting.
cmake&scripts: clarify the error caused by core1 compiling failure.
scripts: ses/iar: use relpath in project file
Added:
soc: hpm6360/hpm6750/hpm6800: add MAC-related definitions in OTP section
soc: reset: add MAIN_ENTRY macro to custom define main entry
soc: add hpm6850 and hpm6830 part.
soc: soc_modules.list: add tamper drivers
soc: Add IAR toolchain support.
soc: add ip feature to soc_modules.list
soc: add hpm_soc_ip_feature.h
soc: driver: ppor: add reset hold operation APIs
soc: clock_driver add the clock_get_divider API.
soc: sysctl: add apis to control clock preservation
soc: toolchains: gcc: ram linker: add ILM last address overflow check
drivers: mcan Add timeout counter support.
drivers: tamper: add tamper driver
drivers: cam: add cam_update_buffer2 API
drivers: opamp: Add user configuration code.
drivers: lcdc: add stride for layer config.
drivers: pdma: add pdma_blit_ex.
drivers:pllctl add out-of-bound check in pllctl driver.
components:uart_lin: add hpm_uart_lin_send_wakeup() API
components: enet_phy: add LAN8720 driver
components: enet_phy: add definition of enet_phy_link_status_t
middleware: cherryusb: host: add dual port support
middleware: cmsis_os2: adapter to rtthread wrapper
middleware: cmsis_os2: update freertos files
middleware: cmsis_os2: adapter to threadx wrapper
middleware: cmsis_os2: adapter to ucOS-III wrapper
middleware: hpm_sdmmc Add eMMC config partition API.
middleware: cherryusb Add IAR toolchain support
middleware: erpc Fix IAR RISC-V support issue
middleware: tflm: add IAR riscv support in flatbuffer
middleware: FreeRTOS: portable:Added IAR portable layer.
middleware: segger_rtt Added EWRISCV support
middleware: hpm_math Add nds_dsp library for IAR.
middleware: lwip: cc: add PACK_STRUCT_XXX definitions for IAR platform
middleware: uC/OS-III: enable plicsw in IAR asm code
middleware: add tinyengine
middleware: threadx: add support for gptmr.
middleware: threadx: add profile support.
middleware: add agile_modbus.
middleware: add cherryrb.
middleware: cherryusb Add missing swap32/swap16 implementation.
middleware: hpm_mclv2: add block type drive motors
middleware: cherryusb: fix usbh_core ep0 buffer index
boards: hpm6200xxx and hpm6750xxx: add board_init_core1() API
boards: add tamper feature and pins init
boards: hpm5300evk: add board_init_console() declaration in board.h
boards: hpm6750evk/hpm6750evk2: add board_dual_usb feature
boards: openocd: add windows guide to *_all_in_one.cfg
boards: openocd: soc: add reset_soc proc
board:add pgpio configuration on hpm5301evklite
samples: drivers: add mono sample.
samples: drivers:mcan Add timeout counter sample.
samples: drivers: tamper: add tamper sample
samples: cmsis_os2: blinky: add rtthread samples
samples: cmsis_os2: add msg_queue sample
samples: cmsis_os2: add mem_pool samples
samples: cmsis_os2: msg_queue: add ucOS-III support
samples: cmsis_os2: blinky: add ucOS-III support
samples: lwip: common: add a task netif_update_link_status
samples: lwip: add MAC address load from OPT MAC area
samples: cherryusb: device: cdc acm: add cdc_acm_uart_com sample
samples: cherryusb: device: add msc sdcard sample
samples: tinyengine: add person detection.
samples: rtos: add threadx gptmr sample.
samples: modbus: tcp: add tcp samples.
samples: modbus: rtu: add rtu sample.
samples: add cherryrb sample.
samples: cherryusb: host: add dual port sample
samples: cherryusb: device: add dual port sample
samples: cherryusb: device: add dual lun msc sample
samples: lwip: ports: rtthread-nano: multiple: add arch-related files
samples: lwip: ports: freertos: multiple: add arch-related files
samples: lwip: common: multiple: osal: add osTaskFunction definition
samples: lwip: add a lwip_tcpecho_multi_ports_rtthread-nano sample
samples: lwip: add a lwip_tcpecho_multi_ports_freertos
samples: lwip: lwip_tcpecho_xxx: add definitions for task priorities
samples: lwip: lwip_tcpecho_freertos_socket: newly add
samples: lwip: lwip_tcpclient: newly add
samples: lwip: add lwip_tcpclient_freertos_socket
samples: vglite: add sample of rotate tiger.
samples: lwip: lwip_tcpclient_freertos_socket: fix failure to run
samples: lwip: lwip_tcpclient: fix failure to run with some release-related type
samples: jpeg: jpeg_encode: add debounce for button.
docs: add cmake doc
docs: hpm5300evk: add qeiv2 sin/cos pins
scripts: support sdk project localization.
cmake: add nds-gcc options to sdk_lib for nds-gcc.
cmake/scripts: add IAR project generation support
cmake: add symbols to specify linker for tools.
cmake: add sdk_*_src_glob.
cmake: add custom targets for localization.
Fixed:
soc: hpm6750: fix segger linker vectors order
soc: hpm_interrupt.h Fix compiling warning for DSP related macros
soc: hpm6750: otp Fix OTP program and read logic
soc: hpm6880: clock Fix wrong enum value for TSNS clock.
soc: clock driver: correct the clock name value for pll clocks.
soc: HPM6280: fix adc/dac clock setting
soc: ppor: fix ppor clear reset flag and set reset type API error
soc: HPM6880: fix i2s clock config driver
drivers: adc12: fix calibration setting error
drivers: cam: DMASA_FB2 need to be assigned whether FB2 buffer is enable or not.
drivers:can correct the logic of disabling re-transmission for ptb & stb.
drivers: qeo: fix driver error
drivers: i2s: ensure valid BCLK before call software reset.
drivers: pdma: fixed OUT_PS[] config.
components: wm8960: invert LRCLK to align with soc I2S.
middleware: uC/OS-III: fix register t0 unsafe.
middleware: ptpd: fix netShutdown error in ptpd initialization
middleware: cmsis_os2: task should call exit interface before exit
middleware: threadx: fix threadx profile RA register save and restore bug.
middleware: hpm_mcl: fix divide-by-zero error.
middleware: cherryusb/tinyusb/usbx: device: fix transfer_len not reset
middleware: cherryusb/usbx: fix dtd return problem
middleware: cherryusb/tinyusb/usbx: fix usb device interrupt should be check active status
middleware: tinyusb: fix ehci cap_reg address error
middleware: tinyusb: fix hid report id
middleware: cherryusb: fix usbd_ep_close not reset ep_enable flag
middleware: cherryusb: fix rndis message length check
middleware: freertos: fix implementation error in xPortIsInsideInterrupt.
boards: hpm6200evk: fix tamper pin config
board: openocd: all_in_one: hpm6800 config file is missed.
boards: openocd: all_in_one: hpm5300: correct soc config name.
samples: threadx hello: fix printing errors.
samples: drivers: ad12/adc16: fix initialization sequence for trigger source, trigger mux and trigger target config
samples: lwip: lwip_ptp: fix netSend error before link-up
samples: dma: fix dma uart init position
samples: drivers:spi:master_trans_large_amound_of_data Fix logic error if SPI support 4GB transfer size
samples: sdxc: add boundary protection for last 1024 blocks test
samples: lwip: common: multiple: fix typo of enet_update_dhcp_state()
samples: lwip: common: single/multiple: fix timeout passed into sys_arch_mbox_fetch()
samples: e2prom: bugfix: base read fail if run perf firstly .
samples: modbus: tcp: use volatile to prevent the compiler from optimizing out key variables
samples: modbus: rtu: fixed failed to run after turning on optimization issue.
samples: power_mode_switch: hpm68xx: fix ddr access issue for wait/stop mode
samples: cherryrb: fixed stack overflow issue
samples: lwip: lwip_tcpecho_multi_ports_ports_rtthread-nano: fix failure to run
sample: jpeg: jpeg_encode: fix that udisk can’t be mounted when first capture.
cmake: correct board search path symbol for core1.
cmake: gcc: fix system include path.
cmake: fix sdk_link_libraries failed to link std lib.
cmake: EXTAR_LD_FLAGS to be added as ld options.
docs: lwip_ptp: v1: salve: fix format error
docs: samples: ppor: change title from sysctl to ppor
docs: hpm6750evk2: fix table display error
[1.4.0] - 2023-12-29:
Main changes since 1.3.0
Tested Segger Embedded Studio Version: 7.32
Changed:
soc: hpm5301: add hpm5301
soc: hpm6880: add hpm6880
soc: HPM6750: pcfg: update dcdc dcm mode config
soc: clock driver: update clock_set_source_divider() and clock_get_source()
boards: add hpm5301evklite
boards: add hpm6800evk
boards: update clock_set_source_divider() to use clk_src_t type param
boards: hpm6750evkmini: use the same uart port as core1 for some samples.
drivers: dao: update driver support new feature on hpm6800
drivers: adc16: update comment about cal_avg_cfg in calibration
drivers: qeiv2: change adc trigmux name x to 0 and y to 1
drivers: femc: add overflow protect to time config
drivers: mcan Enlarge the range of CAN_EVENT_ERROR.
components: serial_nor: add subdirectory in cmakelists
middleware: cherryusb: update to v0.10.2
middleware: cherryusb: rename host and device isr
middleware: FreeRTOS: xPortIsInsideInterrupt() using CSR_MSCRATCH
middleware:hpm_sdmmc Enhanced all speed modes support for SD and eMMC.
middleware: usbx: device: support chain transfer
samples: cherryusb: host: rndis: integrate dhcp thread into ping thread for host rndis ping and iperf sample
samples: adc: temp: add isr for temp out of thresholds
samples: drivers: acmp: optimization for comparing input voltage
samples: lwip: add DHCP macro definition in CMakeLists.txt
samples: lwip_ptp: enable DHCP feature in PTP samples
samples: drivers: qeiv2: update API for adc-qeiv2 pin initialization
samples: bldc_foc: change adc buffer size from 40 words to 48 words
samples: remove explicitly c++ standard setting.
samples: driver: cam: set default cmake build type
samples: lwip: update to Class C static IP adress
samples: tinyuf2: remove unnecessary cache ops.
samples: lwip: lwip_tcpecho_freertos: optimization for API call in a thread-safe way
samples: lwip: lwip_ptp: v1: slave: update static ip
samples: lwip: optimize DHCP enable logic
samples: lwip: opts: adjust the allocation strategy of memory pool
samples: lwip: lwip_iperf: adjust MEM_SIZE for saving memory consumption
samples: lwip: lwip_tcpecho_multi_ports: update the second IP with C class
samples: enet: optimization for PHY selections
samples: dma: update uart rx circle transfer buffer size
samples: drivers: sdxc/emmc Correct doc for emmc sample.
cmake: sdk_link_libraries link libraries for supported tools.
cmake: add project name for hpm_sdk sub directory.
cmake: decouple CMAKE_BUILD_TYPE and linker script.
cmake: ses: remove -Ox from gcc option list.
cmake: set default c++ standard to c++11.
Update CONFIG_HAS_xxx to HPMSOC_HAS_xxx.
segger: enable all warnings.
segger: release: release optimization level use cmakelist config
scripts: ses: set intermediate dir in project file.
docs: remove quick start guide from top level readme
docs: change doc structure.
Added:
soc: HPM5361: add trgm filter shift length feature
soc & drivers: hpm5300: add DMAMUX_SOC_WRITEONLY and TRGM_SOC_HAS_DMAMUX_EN features
drivers: lcb: add lcb driver.
drivers: sdxc add more APIs for timing and power control.
drivers: mipi_csi: add mipi csi.
drivers: cam: add cam_stop_safely API
components: usb: device: add dtd chain transfer
components: panel: enable panel component.
components: camera: ov5640: add mipi interface.
middleware: rtthread-nano: add v3.1.5
middleware: rtthread-nano: add FPU support.
middleware: tinyusb: device: update to support chain transfer
middleware: cherryusb: device: update to support chain transfer
middleware: vglite: add 4.0.49.
middleware: cherryusb: add USB_OSAL_WAITING_FOREVER for sem and mq use
middleware: add hpm_mcl_v2
middleware: lwip: add ptpd v1 & v2
middleware: cmsis_os2: add source files.
samples: mcl: add step motor.
samples: lwip: lwip_ptp: v2: support IEEE1588 V2
samples: cherryusb: add audio_v2_mic_speaker_rtthread sample
samples: cherryusb: host: add hid and msc rtthread samples
samples: cherryusb: host: usbnet: add support ec20 module sample.
samples: cmsis_os2: add blinky sample.
samples: driver: mipi_csi: add mipi_csi.
samples: mcan Support MCAN4-7 loopback testing.
cmake: support custom output file name.
Fixed:
soc: fix cache maintenance at startup
soc: hpm53xx Correct exip API tree offset.
soc: toolchain: missing .fast.* in gnu ld linker script.
soc: fix tbss and tdata section not initialized.
soc: sysctl: sysctl_enable_group_resource() should be check LOC_BUSY
soc: hpm5300 Correct Cache size and Cacheline size.
boards: hpm6750evkmini Fix the issue that eMMC is still 3.3V even 1.8V is selected.
boards: hpm5301evklite correct jlink script device number.
components: camera: power_up is enable by default for ov5640/ov7725.
docs: samples: drivers: add numberic index.
drivers/soc: fix build warning
drivers: i2c: add slave device response judgment for master read/write APIs
drivers: opamp: fix opamp vssa connect error.
drivers: pllv2: fix pllctlv2_pll_is_stable() API
drivers: qeiv2: fix invalid argument check
drivers: dac: fix the upper limit value setting for DAC_OUTPUT
drivers: jpeg: fix pixel format index for out buffer.
drivers: uart: fix not support oversample 32 for rx idle detection on hpm5300
middleware:ftafs Fix SD card init crash.
middleware: mcl: fix path plan error.
middleware: hpm_sdmmc Fix the issue that IO initialization work unstable on HPM6300.
middleware: hpm_sdmmc Fix voltage switch setting issue for SD and eMMC.
middleware: hpm_sdmmc Fix the PWR and VSEL IO initiaization issue. refs:hpm-sdk-#863
samples: sei: fix nikon sample crc calc error.
samples: cherryusb: msc device: add pre-format fat12 file system in u disk
samples: adcx: replace const with a macro for ADC sample cycle
samples: tinyusb:fix the usb host pin init.
samples: motor_ctrl: bldc_littlevgl_foc: program crash.
samples: qeiv2: uvw: fix uninitialized pointer usage
samples: cherryusb: fix semaphore give in isr
samples: drivers: Fix the issue that can error example may block.
samples: uart_irq: fix unable to limit receive large than buffer size.
samples: drivers:sdxc:emmc remove infinite loop for emmc initialization.
samples: drivers: i2s: fix tx underflow during tx start
samples: lwip: lwip_tcpecho_multiple_ports: fix no echo data when receiving large amounts of data
samples: mcl: pwm duty set error.
samples: cherryusb: host: usbnet: fixed when performing a stress test with a large amount of iperf data, will send fai.
samples: cherryusb: audio_v2_mic_speaker_rtthread: fix mic no voice problem
samples: jpeg_decode: add delay after usb pins init for waiting power stable
samples: hfi: hpm6750evk2: fix the motor shake.
cmake: segger: remove workstation specific path info.
cmake/soc: fix heap/stack size setting for andes toolchain.
cmake: ses: correct device name for core1.
[1.3.0] - 2023-09-28:
Main changes since 1.2.0
Tested Segger Embedded Studio Version: 7.32
Changed:
boards: hpm6200evk/hpm6300evk: delete unwanted clock_ahb div set
boards: hpm6750xxx: switch dcdc work mode to dcm mode
docs: sdk: boards: hpm6750evk2: add pps pin information
component: wm8960: support sysclk pre-divider
components: serial_nor: add serial nor flash.
openocd: probes: ft2232: remove trst and srst config.
ip: cam：remove 0x5c MAX_WN_CYCLE register in regs.h
driver: cam: remove invalid register
drivers: i2s: update API
drivers: adc: adc12/adc16: rename adc16_get_busywait to adc16_is_nonblocking_mode
drivers: adc: adc12/adc16: update adcx_init API
drivers: pllctrl: update pllctrl drivers
drivers: spi : add spi enable and disable datamerge
drivers: spi : add spi_set_address_len API
drivers: pdgo Add missing APIs
drivers: uart: update uart rx idle flag process and fifo control
soc: delete_unnecessary_ppor_reset_bit_field
soc: hpm_gpiom_soc_drv.h: delete gpiom_gpio_t soc name
soc: delete DMA_SOC_BUS_NUM Macro
soc: pcfg: update pcfg SCG_CTRL related drivers
soc: hpm6750:startup Enable LMM1 clock before access to LMM1
soc: gcc ld: add memory used size check
middleware: cherryusb: update to v0.10.1
middleware: guix: demo adapts to 800 * 480 resolution
middleware: guix: improve demo display performance
middleware: cherryusb: update for midi descriptor define
middleware: cherryusb: update for midi
samples: drivers: adc: adc12/adc16: speed optimization for oneshot reading
samples: drivers: adc: adc12/adc16： update API call used for nonblocking judgement
samples: drivers: adc: adc12/adc16: update API call related to blocking setting in oneshot mode
samples: drivers: adc: adc12/adc16: reduce the input parameters of init_trigger_target function
samples: drivers: adc: adc12/adc16: update init_oneshot_config
samples: drivers: adc: adc12/adc16: optimization for clearing interrupt status
samples: drivers: pwm: Add pwm clock jitter demo
samples: cherryusb: hid host: separate mouse and keyboard urb
samples: hrpwm: Add demo for updating hrpwm frequency
samples: drivers:mcan Add CAN error handling and refined logic.
samples: mbx: move dualcore mbx sample to multicore folder
samples: cherryusb: update for v0.10.1
samples: motor_ctrl: bldc smc: gcc toolcahin enable fpu.
samples: lwip: lwip_tcpecho_freertos: optimization in a thread-safety way
samples: qeo: update qeo abz frequency configuration
samples: gptmr: add sent_signal sample.
samples: lwip: lwip_ptp: remove the dependency on pps0 pinout
samples: dma_manager: update for use dma_mgr_setup_channel()
samples: drivers: gptmr: pwm_measure: support use dma
samples: lwip: lwip_httpsrv/lwip_https_server: rename project names for uniform naming
samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
samples: flash_algo: update device size.
samples: cherryusb: host: hid: use ep_mps to fill urb
Added:
cmake: ses: support specify custom openocd board cfg file.
cmake: support specifying minimum sdk version in app.yaml.
boards: add hpm5300evk
components: eeprom_emulation: add hpm nor-flash support
components: eeprom_emulation: add eeprom emulation component
soc: add APIs for get or set sysctl resource status
drivers: common: add HPM_ALIGN_DOWN and HPM_ALIGN_UP define
drivers: adc: ad12/adc16: add adcx_set_blocking_read/adcx_set_nonblocking_read
drivers: add encoder position driver
drivers: lcdc: add enable/disable background in alpha blender.
drivers: usb: add api to set dp/dm pin pulldown resistance
drivers: spi: add spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
drivers: spi: add directIO function APIs
drivers: enet: add rx resume API
drivers: adc16: add resolution setting in adc16_get_default_config API
drivers:rtc Add rtc_get_timeval API.
drivers:mcan Add mcan_transmit_via_txfifo_nonblocking API.
drivers: usb: add usb_hcd_set_power_ctrl_polarity() API
drivers: plb: add plb drivers
drivers: linv2: add linv2 driver
drivers: sei: add sei driver
drivers: dmav2: add dmav2 driver
drivers: qeo: add qeo driver
drivers: qeiv2: add qeiv2 driver
drivers: mmc: add mmc driver
drivers: rdc: add rdc driver
drivers: add opamp driver
drivers: bgpr: add related APIs for bgpr
middleware: FreeRTOS: add xPortIsInsideInterrupt() API
middleware: threadx: add definition automatically when enable traceX
middleware: freeRTOS: add use gptmr to generate interrupt
middleware: hpm_mcl: add hfi
samples: drivers: adc: adc12/adc16: add wdog feature
samples: add opamp demo
samples: cherryusb: rndis: host: add iperf sample.
samples: cherryusb: rndis: host: add ping sample.
samples: drivers: adc: adc12/adc16: add hw trigger configuration in sequence mode
samples: eeprom_emulation: add eeprom emulation perf test sample
samples: eeprom_emulation: add base api demo
samples: tracex: add demo for traceX usage
samples: cherryusb: add audio_v1_mic_speaker_midi sample
samples: cherryusb: add midi device sample
samples: drivers: sei: add sei samples
samples: drivers: plb: add plb demo
samples: drivers: mmc: add mmc demo
samples: drivers: qeiv2: add qeiv2 demo
samples: drivers: qeo: add qeo demo
samples: drivers: dmav2: add dmav2 demo
samples: drivers: linv2: add linv2 demo
samples: drivers: rdc: add rdc demo
samples: drivers: pdgo Add PDGO samples
samples: drivers: ewdg Add EWDG sample
samples: lwip: add a lwip_tcpecho_multi_ports sample
samples: motor_ctrl: add hfi
Fixed:
cmake: fix segger default heap and stack size config
cmake: fix add_subdirectory_ifdef arg processing.
doc: boards: hpm6300evk: fix acmp pin info.
boards: hpm6750evkmini: fix board_init_rgb_pwm_pins() problem
boards: hpm6200evk: fix BOARD_G_GPIO_CTRL defined in wrong position
openocd: hpm6750-dual-core: fix expression warning.
component: wm8960: fix clock tolerance process
soc: toolchains: segger: block tls add with fixed order
soc: toolchain: gcc: fix Thread-Local Storage problem
soc: segger linker files: fix heap and ctors initialize
soc: fix interrupt complete operation
soc: pcfg: fix DCDC_PROT[OVERLOAD_LP] bit access
soc: ip: adc12: fix ADC12 threshold setting
soc: HPM6750: fix clock setting and frequency obatining error
soc: HPM6360: fix clock source definitions for ADC16
soc: HPM6280: fix clock source definitions for ADC16
soc: HPM6360: fix obtaining clock source error for DAC
soc: HPM6280: fix obtaining clock source for DAC
drivers: adc16: add bus mode enable control APIs
drivers: adc16: fix ahb setting
drivers: cam: clear the status of CAM should not affect other bits
drivers: trgmux: filter function can’t work.
drivers: src: adc16: fix end count setting
drivers: adc/dac: fix interrupt status clearing
drivers: adc16: fix DMA access format
drivers: sdm: fix over sample rate and signal sync problem
drivers: pwm: fix pwm xcmp enable setting
drivers: pwm: correct external fault polarity setting.
drivers: pwm: add update hrpwm reload shadow api
drivers: spi: fix can’t set change data_bits use spi_set_data_bits API
drivers: ptpc: fix ptpc_clear_irq_status API issue.
drivers: i2c: fix i2c_clear_status API issue.
drivers: gptmr: fix gptmr_clear_status API issue.
middleware: erpc: rpmsg_lite: fix platform_in_isr() error
middleware:hpm_sdmmc Fix the issue sdsc cards are not supported.
middleware: threadx: fix D extend asm code error
samples: usbx: add multi devices and hot plug support
samples: motor_ctrl: fix adc trig invalidate.
samples: lwip: fix TCP reception error when size over 2KB
samples: lwip: DHCP failure in lwip_tcpecho_freertos
samples: drivers: adc: adc12: fix the status flag judgement in isr process
samples: rgb_led: fix cmp shadow error
samples: gptmr: pwm_generate: fix inaccurate duty in high frequency
samples: lwip: low_level_input: fix the network storm issue
samples: timer_basic: fix inconsistent use of defines
samples: drivers: adc: adc16: fix the bit of interrupt status clearing in sequence mode
samples: power_mode_switch: trigger system lowpower for standby mode
samples: touch_panel: fix error data when 5 fingers touch screen at same time.
samples: jpeg: jpeg_decode: fixed lcd display is tore when decoder is running
samples: jpeg: jpeg_decode: malloc out of memory on gcc
samples: drivers:can Fix abnormal behavior on can error sample.
samples: segger_rtt: call board_init_clock.
samples: drivers: acmp: fix one toggle value but multi toggle pulses
samples: lwip_tcpecho_freerstos: fix code stuck with gcc toolchain
samples: jpeg: fix JPEG_USE_UDISK compile error
samples: bldc_foc: fix input value range.
samples: cherryusb: rndis: udp_echo: fix echo extra char
samples: usbx: fix global var placement
samples: power_mode_switch: set to preset_1 after exiting wait mode.
samples: pla: fix pla first pulse abnormal.
samples: plb: fix the first pulse is abnormal.
[1.2.0] - 2023-06-30:
Main changes since 1.1.0
Tested Segger Embedded Studio Version: 7.22
Changed:
boards: hpm6750evk*: decrease core frequency from 816MHz to 648MHz
openocd: soc: hpm6280: simplify dual core release core1 approach.
cmake: segger: configure optimization level according to gcc level.
soc: dmamux: move it from ip to soc
soc: interrupt: adjust irq api. #659
soc: improve svd file
soc: hpm_soc_feature.h: remove ADC16_SOC_TEMP_CH_EN for some specified Socs
components: enet_phy: update the common enet phy header file
components: sgtl5000 and wm8960: update clock setting
drivers: uart: update uart driver
drivers: pdma: improve quality of scale
drivers: adc: adjust wait_dis type in adc16_config_t struct
drivers: enet: update rmii reference clock setting API for ENET
utils: hpm_swap: escape for andes toolchain.
middleware: hpm_sdmmc: add spi sdcard
middleware: motor_ctrl: change the file organization
middleware: motor_ctrl: remove slide control content from foc
middleware: lvgl: upgrade to v8.3.5 (with pdma)
middleware: lvgl: Add direct mode
middleware: cherryusb: update version to v0.8.0
samples: I2S_DMA and I2S Interrupt: update sample behavior
samples: cherryusb: hid host: separate mouse and keyboard urb
samples: cherryusb: increase max interface and endpoint number Configuration
samples: cherryusb: uac2: move setting sampling freq to isr
samples: cherryusb: audio: update descriptor for identification
samples: audio_codec: set codec voice to max and increase irq priority
samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
samples: lvgl_audio_player: update CMakeLists.txt to using noncacheable framebuffer
samples: spi: clean the redundant code
samples: i2c: improve the processing of FIFO in ISR
samples: drivers: uart: update uart_rx_timeout demo
samples: drivers: gptmr: split sample into multiple function samples
samples: drivers: adc: optimization for all macro definitions in applications
samples: drivers: adc: update struct member names
samples: update clock divider setting for ADC-related examples
samples: cherryusb: move vid/pid etc definition to usb_config.h
samples: cherryusb: device: update vid to hpmicro 0x34B7
samples: cherryusb: change API update for v0.8
samples: cherryusb: device: audiov1: change to full speed mode
samples: tinyusb: uac2: update descriptor and sample
samples: lwip: disable mmc interrupt settings
samples: lwip: lwip_ptp: v1: sync precision improvement
Added:
cmake: toolchains: add isa spec 20191213 support.
cmake: ses: support set ses raw option in CMakeLists.txt
cmake: add option to specify board search path.
cmake: generate compile_commands.json file
soc: hpm_soc_feature: add a common macro for ADC12 and ADC16
drivers: cam: add new APIs
drivers: spi: add new APIs
drivers: i2c: add new APIs
drivers: I2S: add i2s_check_data_line_status API
drivers: dma: add dma_set_transfer_src_width_byte_size() API
drivers: gptmr: add output capture APIs
drivers: gptmr: add gptmr_channel_get_dma_request_event api
drivers: adc: add adc16_trigger_pmt_by_sw API
drivers: enet: add some APIs related to interrupt settings
drivers: enet: add a new API for transmisstion
drivers: usb: add macro CONFIG_USB_DEVICE_FS to set full speed mode
components: uart_lin: add uart lin component
components: add smbus
components: add sccb
middleware: lvgl: add macro HPM_LVGL_FRAMEBUFFER_NONCACHEABLE
middleware: add AzureRTOS (threadx/usbx/netx/guix)
middleware: hpm_mcl: sensorless over-zero
middleware: add smc
middleware: hpm_sdmmc Add eMMC support
middleware: hpm_math: add bit conversion function
middleware: add uC/OS-III
middleware: cherryusb: audio: add feedback descriptor
middleware: cherryusb: audio: add param to set endpoint bmAttributes
middleware: microros: add microros foxy sources
samples: drivers: spi: add spi_sdcard_fatfs sample
samples: drivers: spi: add sd sample
samples: add uart_lin
samples: motor_ctrl: sensorless: over-zero demo
samples: cherryusb: add rndis host dhcp samples
samples: drivers: sdxc :emmc Added eMMC sample
samples: drivers: adc12: update irq pattern for sequence usage
samples: drivers: pla: add pla tamagawa demo
samples: drivers: gptmr: add counter_sync sample
samples: drivers: gptmr: add timer_basic sample
samples: drivers: gptmr: add t_shape_accel_decel sample
samples: drivers: dma/gptmr: add trigger dma transfer using gptmr event sample
samples: drivers: uart add uart_rx_timeout sample
samples: i2c: add smbus samples
samples: lwip: lwip_tcpecho_freertos: add self-adaption
samples: cherryusb: hid host: move usbh_submit_urb() out of condition
samples: cherryusb: add composite freertos sample
samples: cherryusb: add rndis freertos sample
samples: cherryusb: add msc freertos sample
samples: cherryusb: add audio v2 mic speaker freertos sample
samples: cherryusb: add hid mouse freertos sample
samples: cherryusb: add hid keyboard freertos sample
samples: cherryusb: add cdc acm freertos sample
samples: cherryusb: add rndis tcp server sample
samples: cherryusb: add rndis device udp_echo sample
samples: cherryusb: add rndis device http_server sample
samples: cherryusb: device: add audio_v2_speaker_sync sample
samples: add several uC/OS-III samples
samples: smc: add smc demo
samples: microros: add subscriber, sevice and publisher
samples: uC/OS-III: mutex
Fixed:
cmake: ses: fix __SEGGER_RTL_vfprintf issue with nds tool in SES 7.20.
soc: hpm6280: Modify the number of PWM cmps.
soc: reset.c: __dso_handle needs to be declared for nds toolchain.
soc: fix max buffer length in sequence mode for ADC
soc: HPM6750: enet soc drv: fix set clock delay settings
soc:hpm6360:sdxc Correct clock divider settting issue
drivers: pla: missing Union Field
drivers: spi: fix the problem of CMD and ADDR configuration order
drivers: i2c: fix clock frequency error rate problem
drivers: i2c: clear CMPL bit in API to avoid blocking the trans
drivers: i2c: fix i2c slave device read and write fail
drivers: i2c: fix read data unexpected multi transition.
drivers: i2c: fix w1c clear status error
driver: usb: fix w1c clear flag error
drivers: gptmr: fix dma request enum definition
drivers: adc: fix logics for judging the validity of arguments
component: uart_lin: fix break signal problem
middleware: cherryusb: fix buffer size error
middleware: lvgl: fix fbbuffer option
samples: gptmr: fix pwm_measure sample compile waring
samples: jpeg: fix interchange format of exif support
samples: jpeg: fix jpeg decode
samples: drivers: spi: fix the problem of CMD and ADDR configuration order
samples: drivers: mcan: can_fd loopback test setting is incorrect
samples: cherryusb: http_server_freertos: fix printf content error
samples: cherryusb: audio: change endpoint attributes for support MACBOOK
samples: tinyusb: msc: increase block numbers for windows format
samples: lwip: lwip_httpsrv: fix reload or refresh error
[1.1.0] - 2023-03-31:
Main changes since 1.0.0
Tested Segger Embedded Studio Version: 7.10
Changed:
docs: add new docs for rtd project.
soc: ip: enet: update the enet register file
soc: ip: adc16: update the adc16 header file
soc: hpm_romapi - Add APIs for configuring remapping, exip regions
drivers: enet: improve APIs related to PPS
drivers: adc: change adc bus blocking interface
drivers: adc: optimize getting oneshot result
drivers: src: update the default config for ADC12&ADC16
boards: rename board-level APIs related to enet
components: enet_phy: rtl8201: update the register file
middleware: hpm_math: update dsp version
middleware: erpc: update to v1.10.0
samples: uart: rename uart_dma_rx_idle to uart_software_rx_idle
samples: uart: add hardware rx idle detection sample
samples: multicore: erpc: core1 add sdk_compile_options(-O1)
samples: drivers: gptmr: update sample output.
samples: lwip: common: arch: ethernetif: update a calling function name
samples:drivers: adc: optimize oneshot handler
Added:
arch: add FPU related APIs
soc/board: add HPM6280 support
soc: HPM6750: acmp: add ACMP section
components: add mt9m114 support
drivers: add raw8 pixel format support
drivers: csr - Implement CSR driver
drivers: adc: adc16: support resolution setting
drivers/samples: add SDM/PLA/CRC/MCAN
drivers: I2C: add new API
drivers: adc: adc16: support resolution setting
drivers: enet: add enet control config for transmission
middleware: cherryusb: audio: update class driver and demo template
middleware: add mbedtls lib files with SDP acceleration
freeRTOS: add support for static allocation
samples: drivers: enet: add a pps demo
samples: cherryusb: add audio samples
samples: add the resolution parameter in all demos with ADC16
samples: add rfft demo
sampels: i2c: add interrupt b2b samples
samples: drivers: i2s: add an i2s_master demo
samples: drivers: i2s: add an i2s_slave demo
samples : rom_api : add sw_gm_api filter
samples: add the resolution parameter in all demos with ADC16
Fixed:
openocd: hpm6300evk: update sdram initialization.
drivers: trgmux: trigmux edge filter setting error
drivers: enet: fix register access error
drivers: adc16: fix the config error of ADC16_CONFIG1
drivers: i2c: fix i2c timing configuration
drivers: SPI: fix SPI status API
drivers: fix gptmr cmp value don’t minus one
drivers: mcan: correct the mcan ext_id filter issue
drivers: I2C: fix issue in i2c_master_address_read API
drivers: Self_ACK cannot be set in CAN driver
drivers: rtc rtc_config_alarm always return error code
cmake: correct source code compilation
soc: toolchain: gcc: initialize heap for SES
soc: gcc linker files: add NOLOAD keyword to noncacheable.bss section
soc: HPM6360: gcc: ld: correct noncacheable region name.
drivers: qei: Fix speed display always zero
middleware: freertos: disable global irq before vTaskStartScheduler
freeRTOS: fix trap when enable float feature
freeRTOS: fix tick lost
freeRTOS: fix segger project build warning
samples: drivers: i2s: fix CFGR config
samples: drivers: fix acmp toggle error
samples: lwip: fix the DHCP issue
samples: uart: fix irq_id judgment
samples: fix the order of uart pin configuration and clock configuration
samples: update spi dma sample
samples: drivers: sysctl: correct reset enable approach.
samples: fix dma_general_transfer sample memory out of bounds
samples: drivers: wdog: Fix logic issue on finding the nearest interrupt interval
sample: audio_codec: decoder_wav: add ‘\0’ to fatfs path
[1.00.0] - 2022-12-31:
Main changes since 0.14.0
Tested Segger Embedded Studio Version: 7.10
Changed:
boards: add version info in banner.
board: lcdc: move panel para to board
components: spi component to support to transfer different width of data in dma handshake mode
drivers: rename dram to femc
middleware: cherryusb update to v0.7.0
middleware: erpc: update for support rtos
middleware: hpm_mcl: update api naming
samples: erpc: rename erpc_matrix_multiply_rpmsg to erpc_matrix_multiply_rpmsg_bm
samples: erpc: reorganize erpc_matrix_multiply_rpmsg samples
samples: erpc: move samples folder to erpc_matrix_multiply_rpmsg
samples: update i2c/spi dma channel and dmamux channel definition
ses: project template: use demo.* as output file naming.
soc: HPM6750: toolchains: update linker files
soc: HPM6360: toolchains: update linker files
Added:
arch: riscv: add read_clear_csr() API
component: add wm8960 support
component: add usb device iso transfer support
drivers: hpm_common: include hpm_sdk_version.h.
drivers: common: add NOP and WFI.
drivers: uart: add api to recv/send byte directly.
soc: HPM6750 linker files: rename rpmsg_sh_mem to sh_mem
cmake: add sdk version header file generation.
middleware: tinyusb: add audio class
middleware: hpm_math: add NN library
samples: erpc: add erpc_two_way_rpc_rpmsg_rtos sample
samples: erpc: add erpc_matrix_multiply_rpmsg_rtos sample
samples: add power mode switch demo. #282
samples: drivers: adc: add a temperature measurement demo
samples: drviers: femc: add sram sample
samples: lwip demo for FreeRTOS
samples: lwip demo of interrupt usage
samples: tinyusb: add uac2 demo
samples: tflm: add face detection demo
samples: tflm: add MLPerf Tiny benchmark demo
samples: lwip: common: feature: add a LPI interrupt process
Fixed:
drivers:interrupt: Fix FPU context crashing in nested irq case
drivers: src: adc: fix adc result in period mode
segger: update app directory structure in SES.
soc: disable irq during cache maintenance
middleware: lvgl: fps calculation to No.
samples: get off level based on board api.
samples: multicore: hello: core1 rgb led does not change correctly.
[0.14.0] - 2022-10-31:
Main changes since 0.13.0
Tested Segger Embedded Studio Version: 6.34a
Changed:
drivers: inc: update adc driver
drivers: gptmr: update reload value
components: enet_phy: optimize APIs
components: enet_phy: dp83867: rename functions
components: conditionally add debug_console
middleware: add cherryusb (0.6.0)
middleware: littlevgl: update to v8.3.1
middleware: fatfs: file name encoding in utf-8
middleware: freertos: support nested irq handling
middleware: hpm_mcl: Optimized motor control foc speed
samples: drivers: dma src move to dma_general_transfer folder
samples: lwip: update all static addresses and all gateway addresses
samples: lwip: lwip_iperf: optimize the interactive log
samples: tinyusb: device: hid_generic_inout: optimize the python script
openocd: HPM6750A1 silicon in hpm6750-dual-core.cfg
header file: update the enet/conctl register files
header file: Update TRGMUX0 pin input source definition
header file: update the ADC12 header files
scripts: ses: organize file in ses according to real path.
cmake: split gcc and ses source
board: bump HPM6750 DCDC voltage to 1200mv
Fixed:
drivers: pdma: fix scale api issue
drivers: i2c: update DATACNT processing
drivers: i2s: fix i2s interrupt workaround in i2s_init
drivers: pwm: fix pwm capture function error
drivers: pwm: fix pwm capture configuration error
drivers: clock: fix error in clock_set_xxx_source
drivers: wdg: timeout calculation error
drivers: trgm_drv: bugfix: include error
drivers: romapi: call fencei after flash erase/write operation
drivers: watchdog: overflow
drivers: usb: host controller initialization issue
drivers: i2s: i2s_enable() issue fix
middleware: tinyusb: src: class: fix the HID report desc macro
samples: drivers: adc: optimize all ADC demos
samples: drivers: adc: fix all channel initializations without a default value
samples: motor_ctrl: hardware trigger api usage error
samples: audio_codec: update clock process for 44100 sample rate
samples: lcdc: boundary pixel is incorrenct
samples: multicore: BOOT_HEADER was missing in multicore core0 example
samples: drivers: i2s: correct audio data if depth < 32bit.
samples: hpm_math: fft_perf_test: Fix error printing information
samples: fix pdm2dao noise problem
samples: lwip: fix the enet throughput degradation
soc: correct address overlapping SES XIP linker file
soc: correct the interrupt context switch issue
soc: fix Lack of interrupt claim for swi
boards: fix some rmii reference clock APIs
Added:
boards: add hpm6750evk2 support
soc: add initfini.c
drivers: lcdc: add y8 support
drivers: spi: update data_length processing
drivers: spi: add api to enable/disable spi dma request
drivers: pmp: Add pmp_config_entry API
components: add ipc_event_mgr
component: spi: add cache maintain
middleware: add erpc
samples: lwip: support self-adaptive port speed and duplex mode
samples: jpeg: support grayscale
samples: drivers: spi: use api to get data length
samples: drivers: spi: add interrupt b2b sample
samples: drivers: mbx: add singlecore samples
samples: drivers: add dma circle transfer
samples: drivers: pwm: add pwm capture demo
samples: provide OTP API demo
samples: add cherryusb hid/msc/cdc samples
samples: add Guomi API example
samples: add erpc sample
samples: add segger_rtt
[0.13.0] - 2022-07-31:
Main changes since 0.12.1
Changed:
drivers: adc: fix sequence and preemption mode
drivers: usb: automatically change transceiver type in host mode
drivers: pwm: modify the interface for setting the pwm shadow register trigger function
drivers: sdxc: driver improvement
samples: jpeg demo update
samples: motor_ctrl: Optimize motor control performance
samples: motor_ctrl: Modify the pwm update method to be hardware triggered
samples: audio_codec: wav: Modify the interface
samples: audio_codec: add dao support
samples: tinyusb: update all USB project names
samples: adc: place DMA buffer in noncacheable
components: usb: update two struct definitions for the hcd_data_t and the dcd_data_t
middleware: littlevgl: update double buffer refresh approach.
middleware: fatfs: enable exfat format
middleware: fatfs: change ‘USB’ to lowercase
middleware: hpm_math: remove cache operations from the ffa interface
scripts: ses: update file path using $(HPM_SDK_BASE)
Fixed:
drivers: gpiom: fix spelling errors in API names
drivers: enet: fix ptp time offset update
drivers: cam: fix store mode configuration
drivers: can: Fix the issue can timestamp cannot be enabled
drivers: gpio: incorrect return type gpio_get_port_interrupt_flags.
middleware: audio_codec: decoder_wav: fix wav codec problem
middleware: tinyusb: fix the alignment of _hcd_data
soc: driver: clock: i2s get clock error
soc: hpm_misc.h: fix incorrect system address mapping.
soc: SVD files: fix SDP peripheral reset value problem
soc: disable vector mode explicitly.
boards: correct device name in ses project
board: correct the printf format for frequency and register base
python: fix ses project generation on windows
samples: adc: fix not working in sequence mode and preemption mode
ses: set obj path for common configuration.
cmake: ses: put app source into separate category in ses.
Added:
components: enet_phy: add rtl8211 driver
components: hpm_spi: add initial SPI component
components: add DMA Manager
drivers: cam: add new API
drivers: uart: add uart_set_baudrate API
drivers: spi: update dma transfer API
samples: tinyusb: host: add a hid demo
samples: drivers: spi: add master_trans_large_amount_of_data example
samples: decoder_wav: Add support for different bit rates and bits
samples: drivers: audio: automatic acquisition of i2s clock frequency
middleware: tinyusb: update portable file for USB host
[0.12.1] - 2022-07-01:
Main changes since 0.12.0
Fixed:
update lwipopt.h for updated enet driver
[0.12.0] - 2022-06-30:
Tested with SES 6.32
Main changes since 0.11.0
Changed:
boards: hpm6360evk has been renamed to hpm6300evk
boards: Use CSR_CYCLE in the clock_delay function
soc: hpm_soc.h: include hpm_common.h
driver: rename hpm_pmu_drv.c to hpm_pcfg_drv.h
driver: spi: change to non-blocking interfaces
driver: dma: update driver to adapt to different DMA instance constraints
components: enet_phy: update dp83867 driver
components: enet_phy: remove rtl8211 driver
cmake: enable nano newlib by default
cmake: move distclean to the beginning
middleware: littlevgl enable PDMA by default
middleware: tinyusb: upgrade to 0.13.0
samples: tinyusb: device: cdc_msc: adjust buffer size
samples: drivers: plic: use gpio toggle count as nested irq
Fixed:
drivers: pwm: fix function name inconsistency bug
drivers: enet: remove “board.h” in enet driver
drivers: clock: Fix bugs in hpm6360 clock driver
drivers: clock: returns wrong adc/dac clock in HPM6360
drivers: dram: failed to configure 8bit mode.
freertos: fix issue about running on core1
boards: hpm6300evk pmp_entry set initial value
middleware: littlevgl: fix pdma cache op issue
middleware: littlevgl: fix doxygen markdown for pdma driver
middleware: lvgl: ses: update ram linker.
middleware: hpm_math: fix ffa cache size error
samples: audio_codec: remove the wrong dependency
samples: FATFS demo cannot support write/read if FATFS passes unaligned buffer address
Added:
samples: add memstress and flash stress
drivers: clock: add implement common delay function based on mcycle and mcycleh register
boards: add hpm6300evk support
boards: hpm6750evkmini: motor control support
soc: add svd files
middleware: lwip: iperf: enable iperf and add udp function
samples: lwip: add lwip_iperf
[0.11.0] - 2022-05-31:
Main changes since 0.10.0-hpm6360-er
Changed:
readme: change the location of the starting document
components: change hal_adc_xx to hpm_adc_xx
drivers: update the I2C driver
cmake: change default rv_arch to rv32imac
cmake: modified in a zephyr-compatible way
drivers: uart: redefined struct with zephyr
cmake: change soc and board name
cmake: ses: support enable ext_dsp in project file.
samples/tinyusb/host: optimize the toggle rate of the blinking led
samples/tinyusb/device: replace mchtimer with board_timer for led_linking_taskk
samples/tinyusb/device: optimize the implement of led_blinking_task
soc: update IP header and soc header files
Fixed:
samples: motor_ctrl: bldc_block: fix some error
middleware: hpm_math: fix andes toolchain compile error
middleware: hpm_math: fix libdsp.a error
middleware: hpm_math: add ext-dsp for SES
samples: openocd_algo: fix func_table placement.
boards: hpm6360evk: correct cpu frequency
boards: fix warning caused by code irregularities
boards: LED status is not the same between hpm6750mini rev-A and rev-B
boards: update board_led_write.
Added:
driver: add spi_setup_dma_transfer() API
middleware: hpm_math: add software fft function
middleware: hpm_math: add ffa to hpm_math
samples: i2c: update the sample b2b
samples: hpm_math: add fft_performance demo
samples: add SPI DMA sample
samples: multicore coremark using debug console only
samples: 1588: add ptp v1 master/slave
[0.10.0_hpm6300] - 2022-05-16:
Main changes since 0.10.0
Changed:
ip register header file update
ses_proj: using generated complete cpu_regs_xml to replace general cpu registers xml
drivers: gpiom: move gpiom_gpio_t into hpm_gpiom_src.h
drivers: update the enet driver
samples: dram: change sdram test address in dma demo
samples: drivers: mbx: exclude flash targets for core0 as well.
samples: lwip: update ethernetif.c
Fixed:
drivers: ptpc: update ptpc_init_timer_with_initial.
drivers: can: bug fix and update
soc: correct vector table inclusion and swi name
env.sh: fix HPM_SDK_BASE setting problem with msys.
samples: sha256_example: failed to run case 13 and 14 with gcc.
Added:
soc: add HPM6360 support
drivers: add ffa, pllctlv2, dac
boards: add hpm6360evk support
components: add adcx module
components/enet_phy: add the RTL8201 driver
samples: drivers: dac, ffa
samples: rgb_red: add evkmini ver B support
[0.10.0] - 2022-04-30:
Main changes since 0.9.0
Changed:
drivers: gptmr: split irq enable/disable interface
drivers: can: 155 Update SJW setting in CAN driver
soc: HPM6750: rename safe stack symbol in link script
components: debug_console: wait uart tx flag on writing.
Added:
drivers: enet: add 1588 support
drivers: can: Add TDC support
drivers: mchtmr: add counter init API.
drivers: dma: add dma_disable_channel() API
middleware: add wav decoder
samples: lwip: add ptp demos
samples: tinyusb: add msc, cdc demo
samples: audio_codec: add wav player demo
samples: add tinyuf2 initial support
samples: add initial uart dma rx idle demo
Fixed:
soc: HPM6750: sysctl: fix cpu lp mode API.
drivers: uart: correct baudrate calculation.
drivers: usb: fix: no response in device mode when a USB cable is pluged out
boards: correct the pin setting related to USB
[0.9.0] - 2022-04-01:
Main changes since 0.8.0
Changed:
drivers: update WDG, UART, DMA, DMAMUX driver
drivers: enet remove enet_intf_selection
drivers: can: support configure bit timing via low-level bit timing parameters
drivers: optimize gpio driver
samples: exclude flash targets for mbx core1
samples: adjust SES project setting for coremark
samples: jpeg: update and integration jpeg decode samples
ses: use relpath for linker script in project file
ses: add HPM device name in generated project file
soc: HPM6750: add an interface selection api
Added:
soc: HPM6750: add ram linker for core1
ses: support to use Andes toolchain
middleware: add hpm_math (replacing hpm_dsp)
samples: add lwip httpd
drivers: add section and alignment general instructions in hpm_common.h
Fixed:
boards: hpm6750evk: fix bldc adc pinmux error
boards : hpm6750evk : pinmux : fix spi init pins error
samples: sdp: fix non-cacheable data initialization issue
samples: littlevgl: fix wrong picture patch in README
[0.8.0] - 2022-03-04:
All changes since 0.7.3
Changed:
rename middleware/sdmmc to middleware/hpm_sdmmc
place isr into .isr_vector section for irq non-vector mode
change csr functions to support llvm
Fixed:
ses: fix issue in register xml
freertor: fix trap handler at non-vector mode
sdxc: fix software reset issue
Added:
add sdk doc
add more sample doc
add multicore demo
i2c/uart: add dma support
add tensorflow lite for microcontroller
[0.7.3] - 2022-02-23:
All changes since 0.7.2
Changed:
freertos: change exception handling
[0.7.2] - 2022-02-21:
All changes since 0.7.1
Changed:
freertos: change freertos irq stack definition, passed in CMakeLists.txt, defined in linker
soc: hpm6750: add DISABLE_IRQ_PREEMPTIVE to check if it needs to enable irq preemption
Fixed:
freertos: disable irq preemption
[0.7.1] - 2022-02-13:
All changes since 0.7.0
Changed:
drivers: adc12: update adc12_prd_config_t
samples: can: update case with interrupt and communication between two boards
Fixed:
drivers: can: fix blocking transcation issue
samples: mbx: support run this example in SES
SES: startup: add fpu enable if abi is set to enable hw fp
Added:
samples: multicore: add flash based multicore example
drivers: can: add apis to recvieve message for non-blocking use
[0.7.0] - 2022-01-30:
All changes since 0.6.2
Changed:
update default CPU frequency to 816MHz from 648MHz
update the ip headers
drivers: gpio: replace gpio_XXX_pins with gpio_XXX_port
drivers: gpio: remove pin level enum definition
drivers: i2s: driver update to remove mclk_div
drivers: ptpc: update driver
drivers: common: update get first set bit API
drivers: uart: split one enable with parameter into enable and disable interfaces
drivers: pwm: change name of output_channel config API
drivers: trgm: split separate API to enable/disable io output
soc: HPM6750: initialize noncacheable data in startup
soc: HPM6750: l1c: update fence.i call
samples: hello_world: add LED flashing
samples: littlevgl: remove lvgl example
Fixed:
hpm6750evkmini: correct refresh cycle number of sdram
hpm6750evkmini: Fix the SDRAM memory range issue in flash_sdram_xip linker file
SES: remove no_relax option for linker, since segger has provide a patch to its ld for ses v6.10.
drivers: gpio: fix read pin issue:
drivers: usb: fix usb disconnection under linux environment
drivers: sdxc: Fixed the compatibility issue on different SD/eMMC cards in the sdcard_fatfs demo
drivers: gptmr: incorrect DMAEN configuration condition
drivers: gptmr: clear CNTRST bit after set.
SDK_DECLARE_EXT_ISR_M cannot work in the c++ file
FreeRTOS: fix ISR_STACK setting
components: touch: gt911: fix gpio write pin call
Added:
SEG: add register definition file in generated embedded studio project
samples: drivers: gpiom: Add example to demonstrate gpiom’s function
drivers: common: add macro to put data into noncacheable sections
middleware: integrate lwip